| Specifications |
| Vertical Specifications |
| Channels | 2 |
| Bandwidth | 60MHz |
| Rise Time | 5.8ns (Approx.) |
| Input Impedance | Resistance: 1 M +/- 2%
Capacitance: (20+/-5) pF |
| Polarity | Normal & Invert |
| Maximum Input | 400V (DC + AC Peak) |
Waveform Signal
Process | CH1 +/- CH2, CH1 x CH2, CH1/CH2, FFT |
| Bandwidth Limit | 20MHz +/-% Typical |
| Horizontal Specifications |
| Sampling Rate | 500MSa/s
Equivalent Max. Sampling Rate is 25GSa/S for all Times |
Range
(1 - 2 - 5 Increments) | 50s/div ~ 10ns/div |
| Mode | Main Sweep, Main Sweep + Delay Expansion Sweep, X-Y |
| Trigger Specifications |
| Source | CH1, CH2, EXT., EXT/5, AC Line |
| Mode | Auto, Normal, Single |
| Trigger Sensitivity | DC: CH1/2 (typical) 1 Div from DC to 10MHz; 1.5div from 10MHz to full
EXT (Typical): 200mV from DC to 40MHz
EXT/5 (Typical): 1V from FC to 40MHz
AC: Attenuates signal below 10Hz
HF Reject: Attenuates signals below 15kHz
LF Reject: Attenuates signals below 150 kHz
Noise Reject: Reduces trigger sensitivity |
| Trigger Level Range | CH1, CH2: +/- Division from center of screen
EXT: +/- 1.2V
EXT/5: +/- 6V |
Trigger Level Accuracy
(Accuracy is for signals having
rise and fall time at max 20ns) | CH1, CH2: +/-(0.3div x V/div)(within +/-4 Division from center of screen)
EXT: +/- (6% of Setting + 40mV)
EXT/5: +/- (6% of setting + 200mV) |
| Edge Trigger | Rising, Falling, Rising & Falling |
| Pulse Width Trigger | Trigger (when >, <, =) on positive or negative pulses
Pulse width range: 20ns ~ 10s |
| Videon Trigger | Trigger on NTSC, PAL, or SECAM standard video signal
Line Range: 1-525 (NTSC), 1 - 625 (PAL/SECAM) |
| Slope Trigger | Trigger (when >, <, =) on positive or negative slope, Set Time: 20ns ~ 10s |
| Overtime Trigger | From the rising or falling edge, Set Time: 20ns ~ 20s |
| Alternative Trigger | Internal Trigger on edge, pulse width, video or slope |
| Cursors and Measurement |
| Voltage Measurement | Vpp, Vamp, Vrms, Vhi, Vlo, Vmax, Vmin, Pre-shoot, Overshoot |
| Time Measurement | Frequency, Rise Time, Fall Time, Positive Width, Negative Width, Duty Cycle |
| Delay Measurement | Delay 1- > 2 
Delay 1- > 2  |
| Cursor Measurement | Voltage Difference between cursors  V
Time Difference between Cursors T
Frequency difference between Cursors 1 T |
| Display |
| TFT LCD Type | 7.0 Inch Diagonal Crystal Display |
| Display Resolution | 800 x 480 Dots |
| General Specifications |
| USB | USB Host / USB Device |
| Power Source | AC 100V ~ 240V +/- 10%, 45Hz ~ 440Hz, Auto Selection |
| Physical Dimensions | 12.3 x 4.25 x 5.6" inches (313 x 108 x 142mm) |
| Weight | 4.6lbs (2.08Kg) |
