STR-P711

DEVELOPMENT BOARD FOR STR711 ARM7TDMI-S MICROCONTROLLER

FEATURES

• MCU: STR711FR2T6 16/32 bit ARM7TDMI™ with 256K Bytes Program Flash, 64K Bytes RAM, USB 2.0, RTC, 12 bit ADC, 4x UARTs, 2x I2C,2x SPI, 5x 32bit TIMERS, 2x PWM, 2x CCR, WDT, up to 50MHz operation
• Standard JTAG connector with ARM 2x10 pin layout for programming/debugging with ARM-JTAG
• USB connector
• Two channel RS232 interface and drivers
• SD/MMC card connector
• Two buttons
• Trimpot connected to ADC
• Two status LEDs
• Buzzer
• UEXT - 10 pin extension connector for Olimex addon peripherials like MP3, RF2.4Ghz, RFID etc. modules
• 2x SPI connectors
• I2C connector
• On board voltage regulator 3.3V with up to 800mA current
• Single power supply: 6V AC or DC required, USB port can power the board
• Power supply LED
• Power supply filtering capacitor
• RESET circuit
• RESET button
• 4 Mhz crystal oscillator
• 32768 Hz crystal and RTC backup battery connector
• Extension headers for all uC ports
• PCB: FR-4, 1.5 mm (0,062"), soldermask, silkscreen component print
• Dimensions: 120 x 80 mm (4.7 x 3.15")

STR-H711

HEADER BOARD FOR STR711 ARM7TDMI-S MICROCONTROLLER

FEATURES

• MCU: STR711FR2T6 16/32 bit ARM7TDMI™ with 256K Bytes Program Flash, 64K Bytes RAM, USB 2.0, RTC, 12 bit ADC, 4x UARTs, 2x I2C,2x SPI, 5x 32bit TIMERS, 2x PWM, 2x CCR, WDT, up to 50MHz operation
• Standard JTAG connector with ARM 2x10 pin layout for programming/debugging with ARM-JTAG
• Perfect solution for developing USB peripherials
• USB connector
• RESET circuit
• RESET button
• Status LED
• Power supply LED
• On board voltage regulator 3.3V with up to 800mA current 
  single power supply: takes power from USB port or extension connector pin
• 4 Mhz crystal oscillator
• 32768 Hz crystal and RTC backup battery connector
• Extension headers for all uC ports
• PCB: FR-4, 1.5 mm (0,062"), soldermask, silkscreen component print
• Dimensions: 50 x 34mm (2 x 1.3")
• Distance between the exntension connectors: 25.4 mm (1")

STR-E912T

DEVELOPMENT BOARD FOR STR912 ARM966 MICROCONTROLLER WITH CAN, USB, RS232, ETHERNET TFT LCD DISPLAY

FEATURES

• MCU: STR912FW44X ARM966E-S 96Mhz, 512K+32K internal Flash, 96K internal RAM, external bus, 9 DMA channels, 10bit ADC, 10/100Mbit Ethernet MAC, 3x UARTS, USB 2.0, CAN,
• 128x128 pixel 12 bit color TFT LCD with backlight
• Joystick with four directions and push action, analogue trimmer potentiometer connected to ADC input
• ETHERNET 100 PHY KSZ8721BL
• RS232 drivers and connectors
• USB connectors
• CAN driver and connector
• SD/MMC card (on bottom of the board)
• IrDA transciever on board (optional)
• Audio Output
• Audio Input
• Speaker on board with volume control
• UEXT connector with I2C, SPI, RS232 and power supply for connecting add-on modules like RF link, MP3, etc available from Olimex
• JTAG interface (optional JTAG-TRACE connector)
• ADC extension port
• Extension ports for all unused microcontroller ports
• External memory bus connector
• Li-ion CR2032 battery connector for the RTC
• Dimensions: 145x130 mm (5.7 x 5.1")

MAXQ-H2000

MAXQ2000-RAX HEADER BOARD

FEATURES

• MCU: MAX2000-RAX up to 20 Mhz( single clock per instruction i.e. up to 20MIPS), low power 190 uA @ 8Mhz, power supply 1.8-2.5V, 16 bit microcontroller with 64 KB Flash (10K re-programming cycles), 2KB RAM, 3x 16bit Timers, 2x UART, 1x SPI, 1-wire, build-in driver for 132 segment LCD
• JTAG connector
• 20 Mhz (on socket) and 32 768 Hz oscillator crystal
• Two on-board power supply voltage regulators supplying +2.5V to core and +3.3V to GPIOs
• PWR_JTAG allow board to be power supplied by the JTAG (if MAXQ-JTAG-USB is used)
• Power supply filtering capacitors
• Extension headers for each uC pin on 0.1" row header
• PCB: FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
• Dimensions: 47x47 mm (1.8x1.8")
• Space between the pin rows: 43.18 mm (1.7")

MAXQ-P2000

MAXQ2000-RAX PROTOTYPE BOARD

FEATURES

• MCU: MAX2000-RAX up to 20 Mhz( single clock per instruction i.e. up to 20MIPS), low power 190 uA @ 8Mhz, power supply 1.8-2.5V, 16 bit microcontroller with 64 KB Flash (10K re-programming cycles), 2KB RAM, 3x 16bit Timers, 2x UART, 1x SPI, 1-wire, build-in driver for 132 segment LCD
• JTAG connector
• 20 Mhz (on socket) and 32 768 Hz oscillator crystal
• 2x RS232 connectors, one can be used for code bootloader
• 1x SPI port on connector
• 1-wire connector
• Buzzer
• Li-io 3V battery connector on board (no RS232 power supply when using this battery)
• Two buttons on ports with interrupts
• RESET button
• Status LED
• Power supply LED
• Two on-board power supply voltage regulators supplying +1.8-2.2-2.5V to core and +3.3V to GPIOs
• PWR_JTAG allow board to be power supplied by the JTAG (if MAXQ-JTAG-USB is used)
• Power supply filtering capacitors
• Extension headers for each uC pin on 0.1" row header
• PCB: FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
• Dimensions:100x80 mm (1.8x1.8")
• Prototype area with GND and 3.3V bus
• Power jack connector for AC/DC power supply

MAXQ-2000STK

MAXQ2000-RAX STARTERKIT EVALUATION BOARD

FEATURES

• MCU: MAX2000-RAX up to 20 Mhz( single clock per instruction i.e. up to 20MIPS), low power 190 uA @ 8Mhz, power supply 1.8-2.5V, 16 bit microcontroller with 64 KB Flash (10K re-programming cycles), 2KB RAM, 3x 16bit Timers, 2x UART, 1x SPI, 1-wire, build-in driver for 132 segment LCD
• LCD display
• JTAG connector
• 20 Mhz (on socket) and 32 768 Hz oscillator crystal
• RS232 connector, one can be used for code bootloader
• SPI port connector
• 1-wire iButton connector
• Buzzer
• Li-io 3V battery connector on board
• four buttons on ports with interrupts
• RESET button
• Two on-board power supply voltage regulators supplying +1.8-2.2-2.5V to core and +3.3V to GPIOs
• Board can be powered by the JTAG (if MAXQ-JTAG-USB is used)
• Power supply filtering capacitors
• Extension headers for each uC pin on 0.1" row header
• PCB: FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
• Dimensions:100x80 mm (1.8x1.8")
• Prototype area with GND and 3.3V bus
• Power jack connector for AC/DC power supply

USB TC-08 Thermocouple Data Logger

The TC-08 Thermocouple Data Logger offers industry–leading performance and is an inexpensive answer to your temperature measuring needs.

Features:

8 channel thermocouple data logger 

Measure from 1 to 160 thermocouples 

Measures from -270 to +1820 °C 

Automatic cold junction compensation 

High resolution and accuracy 

Fast sampling rate — up to 10 measurements per second 

USB interface 

Wide temperature range

The TC-08 thermocouple data logger is designed to measure a wide range of temperatures using any thermocouple that has a miniature size thermocouple connector. Additionally, the TC-08 can also measure other sensors using a 70 mV range.

Featuring built-in cold junction compensation (CJC), the TC-08 has an effective temperature range of -270 to +1820 °C (the actual temperature range depends on the thermocouple being used).

All the benefits of USB

The TC-08 connects to the USB port of a Windows based PC and enables the host PC to automatically detect the TC-08 — avoiding the need for any complex setup procedures. The USB connection also allows the TC-08 to be powered directly by the USB bus — eliminating the need for an external power supply and making the TC-08 ideal for measuring temperatures both in the lab and in the field.

Measure up to 160 thermocouples simultaneously

The TC-08’s USB connectivity allows up to 20 TC-08 USB data loggers to be used simultaneously on one PC — making the TC-08 ideal for use as a large multi–channel temperature acquisition system with a cost per channel significantly lower than other systems of this size.

Fast and accurate temperature data acquisition

With the TC-08 thermocouple data logger your measurements can be made both fast and accurately.

The low conversion time of the TC-08 means up to 10 temperature measurements can be taken every second. Whilst the high (20–bit) resolution ensures that the TC-08 can detect minute changes in temperature.

All you need in one easy–to–use unit

Temperature data acquisition with the TC-08 is very easy — simply plug the TC-08 into a USB port on your computer, connect your thermocouples, and you are ready to measure temperatures.

The easy-to-use PicoLog data acquisition software is supplied with the TC-08 — allowing you to start measuring and recording temperatures with the minimum amount of effort. The intuitive user interface of PicoLog makes it easy for you to set how frequently you want to take a measurement, and the number of measurements you want to take.

Specifications

USB TC-08 Thermocouple Data Logger General Specifications
Number of channels (per TC-08)	8
Maximum number of channels (using multiple TC-08s)	160
Conversion time	100 ms (thermocouple and cold junction compensation)
Temperature accuracy	Sum of ±0.2% of reading and ±0.5 °C
Voltage accuracy	Sum of ±0.2% of reading and ±10 µV
Overload protection	±30 V
Maximum common mode voltage	±7.5 V
Input impedance	2 MΩ
Input range (voltage)	±70 mV
Resolution	20 bits
Noise free resolution	16.25 bits
Thermocouple types supported	B, E, J, K, N, R, S, T
Input connectors	Miniature thermocouple

PC Requirements
Minimum	Processor: 1 GHz Memory: 512 MiB Free disk space: 32–bit: 600 MB, 64–bit: 1.5 GB Operating system: 32– or 64–bit edition of Microsoft Windows XP (SP3), Vista, Windows 7 or Windows 8 (not Windows RT) Ports: USB 2.0 compliant port
Recommended	Processor: 1 GHz Memory: 512 MiB Free disk space: 32–bit: 850 MB, 64–bit: 2 GB Operating system: 32– or 64–bit edition of Microsoft Windows XP (SP3), Vista, Windows 7 or Windows 8 (not Windows RT) Ports: USB 3.0 compliant port

Physical Properties
Dimensions	201 x 104 x 34 mm (7.91 x 4.09 x 1.34 in)

TC-08 Resolution

Thermocouple type	Overall range °C	0.1°C resolution	0.025°C resolution
B	20 to 1820	150 to 1820	600 to 1820
E	-270 to 910	-270 to 910	-260 to 910
J	-210 to 1200	-210 to 1200	-210 to 1200
K	-270 to 1370	-270 to 1370	-250 to 1370
N	-270 to 1300	-260 to 1300	-230 to 1300
R	-50 to 1760	-50 to 1760	20 to 1760
S	-50 to 1760	-50 to 1760	20 to 1760
T	-270 to 400	-270 to 400	-250 to 400

Applications for the TC-08

The TC-08 thermocouple data logger is used successfully throughout the industrial, scientific, medical and the food industries

Narrow Band Powerline Communication Module with Simple MAC

Electrical module of communication line through the media (Power Line Communication) with a TTL UART. This module serves as a converter of Power Line Communication to UART TTL nor vice versa.

specification:
- Voltage electrical lines for communication: 110 VAC 60 MHz, 50 MHz 220 VAC, 12-16 VDC, or without voltage
- Working voltage module is taken from the path of the power line so it does not require an external power supply
- There is a power supply output 5 VDC, 500 mA
- Interfaces: UART TTL
- Baud rate: 600, 1200, 2400, 4800, 9600, 19200
- The length of the frame data communication: 20 Byte (max)
- Data rate: 500 bps (power line)
- Range: up to 1000 meters (depending on the condition of the power line)

iMCU W7200 - ARM32bit Cortex M3

iMCU W7200 - ARM32bit Cortex M3 with hardwired TCP/IP, MAC & PHY

ARM 32-bit Cortex-M3
  - 72MHz maximum frequency (1.25 DMIPS/MHz)
  - 20KBytes Data Memory (RAM)
  - 128KBytes Code Memory
  - Low Power: Support Sleep, Stop and Standby modes
  - 7 timers
  - Three 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input
  - 2 watchdog timers (Independent and Window)
  - SysTick timer 24-bit down counter
  - Full-duplex UART
  - Programmable Watchdog Timer  - CRC calculation unit, 96-bit unique ID
  - GPIO, SPI, USART and USB Interfaces
  - 10BaseT/100BaseTX Ethernet PHY embedded


Hardwired TCP/IP
   - Power down mode supported for saving power consumption
   - Hardwired TCP/IP Protocols: TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet
   - Auto Negotiation (Full-duplex and half duplex), Auto MDI/MDIX
   - ADSL connection with PPPoE Protocol with PAP/CHAP Authentication mode support
   - 8 independent sockets which are running simultaneously
   - 32Kbytes Data buffer for the Network
   - Network status LED outputs (TX, RX, Full/Half duplex, Collision, Link, and Speed)
   - Not supports IP fragmentation 

Dynamixel MX-106T (TTL)

Dynamixel MX-106T (TTL)

H/W Specification

• MCU : ST CORTEX-M3 ( STM32F103C8 @ 72MHZ,32BIT)
• POSITION SENSOR : Contactless absolute encoder (12BIT,360 DEGREE)
• MOTOR : Maxon
• BAUD RATE : 8000 bps ~ 4.5 Mbps
• CONTROL ALGORITHM : PID CONTROL
• Resolution : 0.088°
• Running Degree
• 0° ~ 360°
• Endless Turn
• Weight : 153g
• Dimension : 40.2mm x 65.1mm x 46mm
• Gear Reduction Ratio : 225 : 1
• Stall Torque
• 8.0N.m (at 11.1V, 4.8A),
• 8.4N.m (at 12V, 5.2A)
• 10.0N.m (at 14.8V, 6.3A)
• No load speed
• 41rpm (at 11.1V)
• 45rpm (at 12V)
• 55rpm (at 14.8V)
• Running Temperature : -5℃ ~ +80℃
• Voltage : 10 ~ 14.8V (Recommended Voltage 12V)
• Command Signal : Digital Packet
• Protocol Type
• MX-106T (Half duplex Asynchronous Serial Communication (8bit,1stop, No Parity))
• Link (Physical)
• MX-106T (TTL Level Multi Drop Bus)
• ID : 254 ID (0~253)
• Feedback : Position, Temperature, Load, Input Voltage, etc.
• Material : Full Metal Gear, Engineering Plastic Body
• Standby current : 100 mA

RS485 over Narrowband Powerline Communication Modem (110/220V)

RS485 is widely used in electronics system. PLC-RS485 modem from LinkSprite uses LinkSprite PLC-RS485 module,and isdesigned to send/receive RS485 data over the powerline network. PLC-RS485 is designed to transparently move serial data over the powerline network.

LinkSprite modules have the built-in packet-level repeater function. This feature can greatly extend the coverage of the powerline communication.

LinkSprite modules has both physical and logic addresses. In a network, both physical and logic addresses can be used to address different nodes in the network.

Features

• Fully transparent mode, plug and play coming out of the box without the need to do any programming. 
• Built-in error correction codes.
• Built-in repeater function to extend the coverage.
• Physical and logic address
• AT commands used for advanced configuration.
• RS485 interface to host uP
• FSK(Frequency Shift Keying) modulation used in physical layer
• Low power Design
• RoHS
• Small module size, and easy to be implemented into existing products.

Specifications

Product name	PLC-FSK-RS485-CASE
Interface	RS485
Powerline Voltage	230VAC/50Hz,110VAC/60Hz
Modulation	FSK(Frequency Shift Keying)
Carrier frequency	262K/144KHz
Error Correction	FEC(Forward Error Correction)
Data rate on Powerline	2Kbps
Maximum packet data length	320bytes
Repeater Hops	3 Hops
Transmission distance	300 feets(no repeater)
Support nodes number	65535
LED	Power Line Activity  LED system LED serial port LED

UART to RS-232 interface for xbee

This module is intended to facilitate access XBee module through the RS-232 interface. This card can be used anywhere you want to convert a standard XBee or XBee Pro socket to a wired RS232 connection, not just for the LinkSprite PLC boards.It uses a Sipex SP3232EEN IC to do the 3.3v to RS232 level conversions.

If you need to temporarily or permanently replace an XBee with a wired serial connection, this board is a plug-and-play solution

specification:
- Working voltage: 2.8 - 3.4 VDC (voltage following the work XBee)
- Interface: RS-232
- As an alternative to the DB9 connector, 3 piece pad is provided for accessing RS-232 interface

Thermal Printer Mechanism M-T532AF-011

Thermal printers are not equipped with packing, so that it can easily be applied to custom products.

This printer is suitable for POS applications or ticket printer queue.

specifications:

- Supports paper width: 79.5 mm.

- Capable of printing 640 dots per line.

- Resolution: 8 dots / mm.

- Has autocutter function.

- Print speed of data: 150mm per second.

- Power supply: 24VDC.

- Dimensions: 126.9 mm x 91.9 mm x 57.5 mm.

- Sales Package: printer-T532AF M-011 (not furnished with controller).

Cubieboard simple case

This simple case makes the cubieboard look like a sandwich :)
Size: 10cmx6cm, acrylic.

item list

• Top side x 1
• Bottom side x 1
• Screws x 12 + 4

150M usb wifi module

Small size but stable and good signal, RTL8188CUS/RTL8188EU chip, plug and connect on cubieboard(support hotplug on stock android).

Features:

• Standard: IEEE 802.11b/g/n
• Wireless speed: 150Mbps
• Freq: 2.4GHz
• Channels: 1-13
• Power: 20dBm

Bread board for cubieboard

Bread board for cubieboard, Features of the breadboard:

• Add a vga header on board
• export the 2mm headers on cubieboard to 2.54mm headers
• 1312 isolated cells vias with size 1.1mm/1.8mm 2.54mm pitch

Red Indoor Moving Sign

Moving Sign / LED Display with a width of 95 pixels (7 rows x 95 columns).
specifications:
- Power supply: 5VDC (adapter)
- Number of columns: 95 columns
- Number of lines: 7 lines
- LED light Color: Red
- Dimensions 83.5 x 9.8 x 3.5 cm.
- Available in PC software to organize posts via Serial port (can use a USB to RS-232 Converter).
- Can make custom logo or character
- It has an infrared remote control to adjust the display
- It has an internal RTC

Blue Indoor Moving Sign

Moving Sign / LED Display with a width of 95 pixels (7 rows x 95 columns).

specifications:

- Power supply: 5VDC (adapter)

- Number of columns: 95 columns

- Number of lines: 7 lines

- LED light Color: Blue

- Dimensions 83.5 x 9.8 x 3.5 cm.

- Available in PC software to organize posts via Serial port (can use a USB to RS-232 Converter).

- Can make custom logo or character

- It has an infrared remote control to adjust the display

- It has an internal RTC

Pink Indoor Moving Sign

Moving Sign / LED Display with a width of 95 pixels (7 rows x 95 columns).

specifications:

- Power supply: 5VDC (adapter)

- Number of columns: 95 columns

- Number of lines: 7 lines

- LED light Color: Pink

- Dimensions 83.5 x 9.8 x 3.5 cm.

- Available in PC software to organize posts via Serial port (can use a USB to RS-232 Converter).

- Can make custom logo or character

- It has an infrared remote control to adjust the display

- It has an internal RTC

Low cost indoor P4 moving sign

Moving Sign / LED Display with 128 pixels wide (8 rows x 128 columns).

specifications:

- Power supply: 5VDC (adapter)

- Number of columns: column 128

- Number of lines: 8 lines

- LED Light Color: Red

- Dimensions 51.8 x 5.3 x 2.2 cm.

- Available in PC software to set the posts through the USB port.

3 Color dual line indoor LED moving display

Moving sign display module can display three colors on each dot.

Specifications: 
- Color: tricolor (red, amber, green) 
- Number of lines: 16 lines 
- Number of columns: column 160 
- Capable of displaying simple graphics 
- Available in PC program to fill in the characters into the display module 
- Can create their own characters to be displayed to the display module. 
- Dimensions: 125.5 cm x 4cm x 16cm

Miniature Thermocouple Connectors Flat Pin

Omega SMPW thermocouple connectors are mini size flat 2 pin TC connectors designed to connect temperature sensor instrumentation and a temperature controller or process control HMI automation panel. Male 2 pole TC plugs and matched female 2 prong TC jack pairs are stock items. 
Standard size round pin OSTW plugs, jacks and thermocouple TC connectors are also available - see related products below.
Accessories for wire, crimp, cable clamp, grommet and strain relief are in the accessories link. 
SMPW is manufactured as a form fit replacement for the legacy SMP model. 

Features:
• Color-Coded for ANSI or IEC
• Captive Cover Screws
• Write-on Window
• Chisel point connection pins
• Accepts Stranded or Solid Wire up to Size 20 AWG
• Quick Connect Contact Washers Internal Wire Divider
• SMPW Series , Glass filled Nylon construction is rated to 220°C (425°F)
• HMPW Series, Liquid Crystal Polymer (cadmium-free) construction is rated to 260°C (500°F)
• Form Fit Replacement for Legacy SMP Model

LIPO 11.1V1800mAh LB-12

LIPO 11.1V1800mAh LB-12 Description -     Lithium Polymer rechargeable battery (for DARwIn only). -     PCM is incorporated to protect the batteryfrom overcharge, discharge, and excessive current. -     Cannot be used for Bioloids because it the connectorand size differs. -     Battery cover and extension cable are notincluded. -     Can be recharged with LBC-10 BatteryCharger. Components Component Quantity Battery LIPO 11.1V 1800mAh LB-12 1 * Battery Charger (LBC-10) sold separately Specifications Weight 106g Size 88 x 35 x 26mm Voltage 11.1V Current 1800mAh Discharge rate 5C Etc. PCM built-in (overcharge, discharge, excessive current protection)  Precautions ** Cannot be recharged via DARwIn and needs to be charged using a specific charger (LBC-10).  -     Do not drop or fold parts of the battery or its parts. -     Do not fold the end of the sutured portion. -     Do not apply heat, water or any other liquid on the battery. -     Do not place in the microwave, washing machine or dryer. -     Do not use damaged batteries. (inflated,deformed, damaged, etc) -     Do not short circuit the polarity. -     Do not take the battery apart. -     When charging, make sure the battery is connected into the correct polarity. -     Do not charge when the battery is hot. Please charge after it has cooled off. -     Battery will not charge when connected to the robot.   Storage Precautions - Detach the battery from the robot or controller when storing away. - When storing away the battery for a long time, make sure the battery life is around 50%. - Do not store it in wet or hot places. ** LIPO 11.1V 1800mAh LB-12 has a warranty period of 6 months. Compatible Products -  Robot :DARwIn-OP -  BatteryCharger: LIPO Battery Charger LBC-10 ** NOT compatible with the CM-Seriescontrollers.