LED Magnifier Lamp Aoyue 927

LED Magnifier Lamp Aoyue 927

3x Magnification / 15x Magnification (PCB-Components)

This model 927 distinguishes itself by colourfast light, whereby no irritations can occur.

The lamp is best suitable for the deciphering of small components on the board or for soldering without additional aids.The LED lamp can be used for checking if the joints on the board have flaws, which is not possible with the normal eye. It has an incredibly low energy consumption of 2-3 Watt, through which a contribution to environmental protection and money saving is achieved. The Aoyue 929 is additionally equipped with a lamp cover, which protects the lamp against damage and dirt.

Technical Specification:

Input 230 Volt +/-10% / 50 Hz +/-2Hz

Energy requirement 2-3 W

LED number 37

Light colour white

Magnification x3 / x15 (Teilbereich)

Housing colour black

Weight 2,2 kg

Diameter of the magnifier 85 mm

Aoyue 9080+ Ultrasonic Cleaner

Aoyue 9080+ Ultrasonic Cleaner

Features :

• Uses ultrasonic waves.

• Up to 4 liters of cleaning capacity.

• Heated cleaning function.

• Programmable cleaning time from 0 to 30 minutes.

• Adjustable temperature power and time settings with digital display.

• Suitable for cleaning electronics tools, circuit boards, jewelry/accessories, medical tools and 

other metals parts.

SPECIFICATIONS

• POWER INPUT: available in 110V / 220V
• WEIGHT: 6 Kg
• MAIN STATION DIMENSION: 320 x 220 x 170 mm
• TANK DIMENSION: 300 x 100 x 150 mm

ULTRASONIC CLEANER

• HEATING POWER: 600W
• CLEANING POWER: 120W
• TEMPERATURE RANGE: 70°C
• HEATING ELEMENT: PTC Heater
• CLEANING TIME: 10s-600min
• OPERATION FREQUENCY: 35Khz
• TANK CAPACITY: 4 Litter

Aoyue 486 Smoke Absorber

Aoyue 486 Smoke Absorber

Features:

• Quickly absorbs and removes the toxic gases released during soldering.

• Unique back laid air filter packs with minimum air resistance, higher suction power that ensures excellent working environment.

SPECIFICATIONS

• POWER INPUT: available in 110V / 220V
• WEIGHT: 1 Kg

SMOKE ABSORBER 

• POWER CONSUMPTION: 20W
• PUMP TYPE: Brushless Motor

AOYUE 328 WORKING PLATFORM

AOYUE 328 WORKING PLATFORM

Features:
 Made from anti-static materials.
 Stepless screw clamp table fixing the circuit boards steadily.
 High position table design effectively protects the table top from being damaged by welding and hot air.

SPECIFICATIONS

• DIMENSIONS: 200 x 220 x 50 mm
• WEIGHT: 2 Kg

Odroid-C1 3.2inch TFT+Touchscreen Shield

Fully assembled 3.2inch display with 320x240 pixels TFT LCD and a resistive touch overlay. Just plug it on top of ODROID-C1. 2x13 tall female header is already soldered on the PCB. 

Fast 30Mhz SPI is used for the faster frame rate.

You will need an official Ubuntu image to configure it. 

You can simply download the Kernel updates and configure your ODROID-C1 for this display shield. 

Please follow the step by step guide from the WiKi. If not, the display doesn't work.

http://odroid.com/dokuwiki/doku.php?id=en:c1_lcdshield

Note: this display is NOT compatible with Android platform.

ODROID-C1 Case Blue

For those who appreciate the beauty of the naked PCB board – but still wants to protect the ODROID-C1 from dust and the elements. The semi-transparent case has openings for all outputs including the GPIO port making it a great fit projects that are connected to external hardware.

The cover of GPIO part can be easily removed by simple cutting of a few ribs.

Strong & Durable Poly Carbonate Plastic

Size : 90 x 59 x 28 mm

Weight : 32g

Online Order  https://tokopedia.com/rosesana/odroid-c1-case-blue

ODROID-SHOW2

The ODROID-SHOW is the Arduino compatible that lets you see what your ODROID or PC is thinking using a small 2.2” TFT LCD.   ONLINE ORDER

You can show colorful texts and pictures via USB interface with VT100/ANSI style commands without big HDMI monitor. You can connect this tiny display to your ODROID as well as Mac, Linux PC, Windows PC even an enterprise server.

The form factor is designed for stacking on the ODROID-U3 and it comes with some PCB spacers and a USB cable.

There are I2C, ADC, GPIO pins for further expansion. We will introduce an add-on board with some sensor chips.

You can make it portable device with on-board charger by adding a 750mAh Li-Po battery. Because of very low power consumption, this is very useful for Wearable projects.

ONLINE ORDER  https://tokopedia.com/rosesana/odroid-show2

750mAh Battery for Odroid

Compatible with ODROID-W / ODROID-SHOW2

• Lithium Polymer rechargeable cell with a protection circuit.
• Capacity : 750mAh
• Dimension: T:8.2 x W:20.5 x H:49.5 mm (+/- 0.2mm tolerance)
• Lead wires: AWG#30, 50mm
• Connector : Molex 51021-0200

Weather Board for Odroid

Add-on sensor board for ODROID-SHOW

The Weather board is an easy to use ODROID-SHOW Add-on that grants you access to

• UV Index, 
• Barometric pressure, 
• Altitude, 
• Relative humidity, 
• Illumination,
• Temperature. 

- Dimension is only 20 x 20 mm
- Sensors : Si7020, BMP180, Si1132
- Recommended working voltage : 2.7 ~ 3.6 Volt

ONLINE ORDER  https://tokopedia.com/rosesana/weather-board-rev01

Odroid-W Docking Board with TFT LCD

Docking board for ODROID-W   ONINE ORDER

- 4 x USB host ports 

- 10/100 Ethernet port

- 2.2inch 320x240 QVGA color TFT LCD assembled

- Audio stereo jack (3.5mm)

- UART port for serial console

- Board size : 60 x 60 x 21mm including LCD module

* You need a W Connector Pack to stack the ODROID-W on the Docking board.

* Highly recommend 5V/2A Power Supply for stable power input

ONLINE ORDER  https://tokopedia.com/rosesana/odroid-w-docking-board-dengan-2-2-inch-tft-lcd

Odroid-W Connector Pack

Compatible with ODROID-W

Header sockets can be used for connection to the Docking Board or your own base board design. 

26pin header pin can be mounted on top side of ODROID-W and it makes compatible with many RPi compatible shield boards.

USB host connector can be mounted on top side of ODROID-W or bottom side.

You need a soldering iron and lead.

Dekko DT2234L non contact digital tachometer

Dekko DT2234L non contact digital tachometer

Specifications:
- Measure range: 2.5 to 99, 999RPM ( r/ min)
- Resolution 0.1 RPM ( 2.5 to 999, 9 RPM) , 1RPM ( over 1.000 RPM )
- Accuracy : + / - ( 0.05% + 1 Digit )
- Display 5 Digits, 18mm ( 0, 7 " ) LCD
- Battery: 3x1.5V AA ( UM-4)

Aoyue 2663B

Universal Soldering Iron Holder Aoyue 2663B 

Place of AOYUE soldering is made of stainless steel. Equipped with dual tip cleaning sponge and a roll of solder is brass. There are places to put the roll tin.

S202S01F solid state relay

SHARP S202S01F solid state relays are designed with infrared emitting diode (IRED), phototriac detector and a triac output. This diode is ideally used to adjust the load to the AC voltage.

specifications:

- Power supply control: 1.2 VDC

- Power supply load: 80-240 VAC

- The load current: 8 A

- Configure output: -

- Features: Output current, IT (rms) = 8.0A, non-zero crossing functionary, high isolation voltage between input and output, lead-free terminal components are available Also, a screw hole for heat sink.

- Led indicator: No

- Built-in snubber: Yes

G3MC-202PL DC5 Solid State Relays SPST-NO 5VDC/100-240VAC 2A Built-in snubber

OMRON G3MC-202PL DC5 Solid state relay 5 VDC configuration with single-phase solid state relay (SPST).

specifications:

- Power supply control: 5 VDC

- Power supply load: 100-240 VAC

- The load current: 2 A

- Configure output: -

- Features: Small bottom surface area, the DC input AC output, approved by UL and CSA, DC input / AC output

- Led indicator: No

- Built-in snubber: Yes

Banana Pi HDMI line

HDMI cable

specifications:
- Black
- Length: 1m

Banana pi I2C GPIO extend board

Based modules to expand 8 Bidirectional PCF8574 IO at Banana PI. Users can select the voltage at 3.3V or 5V modules for IO voltage.
Specs:
- Power supply: 2.5V - 6V
- IO Voltage: 3.3V or 5V
- Interface: I2C

Banana pi IO extend Board

Extend IO Board for Banana Pi, can be used for the Raspberry Pi.

specifications:

- Power supply: 2.4V - 5V

- IO Voltage: 3.3V

- Interface: SPI

- Expande 32 unidrectional IO

Banana pi Prototyping Pi Plate

Module developers designed specifically for Banana Pi available pad arrays for application circuit, experiment or create a prototype product.

Banana Pi sata line

Sata cable is suitable for connecting Banana Pi with a 2.5-inch hard drive.

Specifications:

- Length: 30 cm

Banana Pi GPIO J12 line

12 lines Flat Cable with IDC Socket on both ends

specifications:
- Cable Colour: Grey
- Number of lines: 12
- Cable Type: Flat
- Cable length: 25 cm

Banana pi GPIO extend module

GPIO expansion module serves to facilitate communication Banana Pi with Breadboard

Banana pi GPIO extend board

Banana GPIO expansion module Pi to Breadboard. This module converts the voltage from 3.3V IO from becoming 5V.

UNO extend board for Banana Pi

UNO GPIO extend board ,can use on raspberry pi board

UNO extend ATmega328-based board is compatible with the Arduino UNO code and peripherals. This board helps Banana Pi to be able to connect to the Arduino sheild.

specifications:

- Power supply: 3.3V - 4.5V

- Based microcontroller / microprocessor: ATmega328

- Port interface: SPI

Banana Pi GPIO com3 line

Flat ribbon contents of 26 at the end there IDC connector
specifications:
- Cable Colour: Grey
- Number of lines: 26
- Cable Type: Flat
- Cable length: 25 cm

Banana Pi AV line

Color black, length 1 meter for Audio/Video (banana Pi)

Banana Pi CSI DSI line

White markings flat cable to connect Banana Banana PI Pi with camera
specifications:
- Cable Colour: White
- Number of lines: 40
- Cable Type: Flat
- Cable length: 25cm

Banana pi CPU heat sink

Banana pi CPU heat sink

USE:

-- The product is used for Banana Pi only.
-- It dissipates heat off your Banana Pi in high efficiency.

FEATURES:

-- High heat radiation efficiency；
-- ultra slim;
-- ultra light;
-- Simple installation;
-- Perfectly matched to Banana Pi's CPU and RAM;

MATERIAL:

-- The heat sink body is made of 100% Aluminum;

COLOR:

-- Silver Gray;

SIZE:

-- 22mm*22mm*3.0mm

banana pi camera use OV5640 chip

HD camera module for Banana Pi. The camera uses an image sensor OV5640 CMOS technology. Connecting with Banana Pi through CSI.

specifications:

- Camera 5 Megapixel resolution

- Sensor array: 2592 x 1944

- Max frame rate: 1080P 30fsp @ 24MHz

- Image formats: JPEG, PNG, YUV420, RGB888

- Fucking Format: H.264 Raw

- Interface: CSI

- Dimensions: 36 x 32 x 10 mm

3.5MM to RCA Audio Cable for Banana Pi

3.5MM to RCA Audio Cable for Banana Pi

USE:

-- The product is used for Banana Pi OTG.
-- USB OTG: USB On-The-Go;

FEATURES:
-- Port A: 3.5 mm headphone jack male;
-- Port B: 2 RCA male;
-- High speed transmission;
-- Plug and play;
-- Perfectly matched to Banana Pi 3.5mm audio port and TV RCA port;

MATERIAL:
-- wire is made of copper;
-- wrapping is PVC;

SIZE:
-- Length: 1.1MTS;
-- Width: 5.0mm;
-- Height: 2.5mm;

WEIGHT:
-- Net weight: 32g;

Banana Pi ABS Plastic Case

Banana Pi ABS Plastic Case

USE:

-- The product is used for Banana Pi only.
-- It protects your Banana Pi perfectly;

FEATURES:

-- High quality;
-- Fashion design;
-- Professional design;
-- Glass style surface;
-- Ultra light;
-- Simple installation;
-- Perfectly matched to Banana Pi;

MATERIAL:

-- It is made of 100% ABS material;

COLOR:

-- Black;

SIZE:

-- After assembling: 10.8cm*7.0cm*3.3cm;
-- Wall thickness: 2.0mm;

WEIGHT:

-- Net weight: 55g;

Banana Pi 5V 2A DC adapter for EU

USE:
-- The product is used to supply AC power into DC for BPi.
FEATURES:

-- Input: 100-240VAC 0.3A 50/60HZ;
-- Output: 5V2A;
-- European Standard Plug;
-- usb output
COLOR:
-- Black;

TEC1-01708 Thermoelectric Cooler Peltier Module

Module producing heat and cold temperatures

specifications:
- Power supply: 2 V (max)
- The input current: 8.5 A
- Maximum difference in temperature: 68 ° C
- Dimensions: 15 x 15 x 3.3 mm
- One side generates heat and produces cold side

more about TEC: http://2r-he.blogspot.com/2010/08/peltier-thermoelectric-cooler.html

TEC1-01708S Thermoelectric Cooler Peltier Module

Module producing heat and cold temperatures

specifications:
- Power supply: 2 V (max)
- The input current: 8.5 A
- Maximum difference in temperature: 67 ° C
- Dimensions: 15 x 15 x 3.7 mm
- One side generates heat and produces cold side

TEC description http://2r-he.blogspot.com/2010/08/peltier-thermoelectric-cooler.html

Thermoelectric Cooler Peltier Module - TEC1-12703HTS

Module producing heat and cold temperatures

specifications:
- Power supply: 15.4 V (max)
- The input current: 3.3 A
- Maximum difference in temperature: 67 ° C
- Dimensions: 40 x 40 x 4.7 mm
- One side generates heat and produces cold side

more description:
http://2r-he.blogspot.com/2010/08/peltier-thermoelectric-cooler.html

G5SB-14 5DC OMRON 5VDC SPDT relay

5 VDC relay configuration with single pole double throw (SPDT) OMRON production.
specifications:
- Coil voltage: 5 V
- Flow coil: 80 mA
- Contact Voltage: 30 VDC / 250 VAC
- Flow contact: 5 A
- Number of pins: 5
- Configuration: SPDT
- Dimensions: 20.3 x 10.3 x 15.8 mm

G5LE-14-DC5 OMRON 5VDC SPDT relay

5 VDC Relay configuration with single pole double throw (SPDT).

specifications:
- Coil voltage: 5 V
- Flow coil: 79.4 mA
- Contact Voltage: 125VDC / 250VAC
- Flow contact: 10 A
- Number of pins: 5
- Configuration: SPDT
- Dimensions: 22.5 x 16.5 x 19.0 mm

G6RL-14-ASI-DC3 OMRON 3VDC 8A SPDT relay

3 VDC Relay configuration with single pole double throw (SPDT) OMRON production.

specifications:
- Voltage coil: 3 V
- Flow coil: 73.3 mA
- Contact Voltage: 300 VDC / 400 VAC
- Flow contacts: 8 A
- Number of pins: 5
- Configuration: SPDT
- Dimensions: 28.5 x 10.0 x 12.3 mm

G5V-2-DC12 Omron 12VDC DPDT relay

12 VDC Relay with a double pole double throw configuration (DPDT), OMRON production.
specifications:
- Coil voltage: 12 V
- Flow coil: 41.7 mA
- Contact Voltage: 30 VDC / 125 VAC
- Flow contacts: 2 A
- Number of pins: 8
- Configuration: DPDT
- Dimensions: 20.5 x 10.1 x 11.5 mm

VH-75T UHF RFID reader Handset

The reader can easily online link to smart terminals(such as smartphone, tablet PC and etc
Features:
1.online linking to PDA、smartphone、tablet PC can reduce repeat purchasing cost;
2. support tags reading and writing with protocol ISO-18000-6B、ISO-18000-6C（EPC G2）;
3. easy to read tag；
4. low cost, cheaper than handheld reader with PDA;
5. industrial structure, reliable design, adapt to harsh work environment;
6. provide with Android OS demo software and SDK.

Description
Model #	VH-75T
Performance Index
Frequency range	865-868MHZ，902-928MHZ（can be customized）
FM mode	FHSS or fixed frequency, can be set by software
RF output	30 dBm, adjustable
Communication interface	USB1.1，bluetooth IEEE802.15 with rate 1Mbps
Tag operation performance
Read/Write distance	Read>500-700cm，Write>20cm
Protocol	ISO-18000-6B、ISO-18000-6C（EPC G2）
Mechanical electrical performance
Dimension	180(L)*55 (W)*30(H)mm
Power supply	Chargeable polymer battery（3.7V,3200mAH）
Tag reading hint	vibration、buzzer、LED
Memory card	2G(MiniSD)
Standby time	150 hours，scan times for one-time charge：5000 times
Weight	250g
Humidity	5% to 95%, non-condensing
IP rating	IEC IP65
Operating temperature	-20ºC to +50ºC
Storage temperature	-25°C to +70°C

VH-770 UHF Handheld Reader

• UHF RFID handheld reader support ISO 18000-6C（EPC C1 G2）protocol，support inbuilt Windows CE6.0 OS
• Features:

1. Support kinds of different modules optional, adapt to users’ different requirement;
2. Support EPC Class1 Gen2 / ISO18000-6C；
3. Output power can be adjustable by software，10～28dBm，1dBm step by step；
4. Read distance up to 7 meters（96mm*15mm tag）；
5. Integration with Wifi 802.11b/g；
6. Ergonomics design handle, easy to handhold, relieve user’s feeling of fatigue to operate；
7. Continuous working time up to 4 hours, standby time about 20 days；
8. Industrial structure with high reliable design, meets harsh work environment requirement.

Description
Model#	VH-770
performance & physical parameter
Protocol	EPC Class1 Gen2/ISO18000-6C
CPU	High speed ARM platform，main frequency 800MHZ
OS	Microsoft® Windows CE 6.0
RAM	512MB
Memory card	4G Micro SD（standard configuration），support 32G at max.
Barcode module options
1D module	Symbol SE955
2D module	Honeywell 5180 (optional)
WIFI	WLAN 802.11 b/g （standard configuration）
Extend module	GPRS module，2.45G module（optional）
Communication interface	USB Slave
Audio	Typhoon, support multi-media function
Dimension	200mm* 80mm*145mm
Weight	703g(excluding charging base)
Key	27 keys
Display & physical parameter
Screen	4 inch TFT LCD（480*800），resistive touch screen, backlight adjustable
Battery	Rechargeable lithium polymer battery（3500mAh @ 7.4V ）
Operation temperature	-20° C～+50° C
Storage temperature	-30° C～+70° C
Humidity	5%～95% non-condensing（25℃）
Accessories	9V/1A charging base，USB cable
Frequency parameter
US	902 ～928MHz
CN	920 ～ 925MHz
EU	865 ～ 868MHz，other standard can be customized
Read distance	7 meters at max.（tag dependent）
Write distance	3 meters at max.（tag dependent）