General-purpose Zener diode NZX7V5B

Zener diode NZX7V5B (7.4V, 500mW)  in a SOD27 (SC-40) small hermetically sealed glass package.

DC to DC Boost Converter Step-Up Output 5V-35V

DC-DC Boost Converter Step-Up Power Module Output 5V-35V

Module DC-DC voltage booster is equipped with a chip XL6009E1 2nd generation with high-frequency switching technology.

specifications:

- Input voltage: 3V - 32V

- Max input Current : 4Amp

- Output voltage: 5V - 35V

- Equipped 4A MOSFET switch tube, so that the level of efficiency can be achieved up to 94%

- The switching frequency up to 400 Khz

- Dimensions: 43mm x 21mm x 14mm

36 pin Male Centronic Connector

Centronic 36 pin Male Connector

36 pin connector to the cable (IDC Socket / flops)
specifications:
- Production Centronic
- The number of pins: 36-pin
- Configure Printer Port connector according to the 36-pin

MPC17529EVEL cmos motor driver

Bipolar CMOS motor drivers are equipped with the technology under voltage detection and shutdown circuit.

• Motor Type - Stepper Bipolar
• Motor Type - AC, DC Brushed DC
• Function Driver - Fully Integrated, Control and Power Stage
• Output Configuration Half Bridge (4)
• Interface Parallel
• Technology CMOS
• Applications Battery Powered
• Current - Output 700mA
• Voltage - Supply 2.7 V ~ 5.6 V
• Voltage - Load 2 V ~ 6.8 V
• Operating Temperature -20°C ~ 150°C (TJ)
• Mounting Type Surface Mount
• Package / Case 20-SSOP (0.209", 5.30mm Width)
• Supplier Device Package 20-VMFP

DF02STRR16 1Amp bridge rectifier diode

1 Ampere diode bridge/rectifier with a maximum voltage of 200 Volt

• Bridge Rectifiers 1-PHA 200V 1A D-71
• Current of 1 A
• 4- SMD packaging (DFS)
• Input peak voltage of 200 V (Max)

UART Fingerprint Reader

UART Fingerprint Reader is a fingerprint reader module with stability and high speed identification (High speed identification and high stability), because it uses a processor STM32F205. This module is one intelligent module that has a variety of functions such as fingerprint recording, image processing, feature extraction, template generation, template storage, Finger matching and Searching

ADM3202ARUZ transceiver IC (RS-232 2-channel)

ADM3202ARUZ is transceiver IC (RS-232 2-channel) hi-speed  who works at a level 3 - 5.v volts.

specifications:

- Function: RS-232 Transceivers Full Duplex

- Data Rate: 460 kb / s

- Number of Drivers: 2 drivers

- Number of Receivers: 2 Receiver

- Operating Supply Voltage: 3 V to 5.5 V

- Operating Supply Current: 3 mA

- Operating Temperature: - 40 ° C s / d + 85 ° C

- Number of Transceivers: 1 Transceiver

- Protocol Supported: RS-232

- Receiver Signal Type: Single-Ended

- Supply Type: Single Supply

- Packaging: TSSOP-16

SI-8050S Step Down 5V Switching Regulator chip

ALLEGRO SANKEN SI-8050S Buck (Step Down) Switching Regulator, Fixed, 7V-40V In, 5V And 3A Out, TO-220F-5

The SI-8050S is a full-mould separate excitation Switching IC with phase correction and output voltage adjustment performed internally. The SI-8000S series IC has built-in reference oscillator (60kHz), built-in over-current and thermal protection circuits and built-in soft start circuit (output ON/OFF control).

• 79 to 91% High efficiency
• Requires only 4 external components
  

Tech Specs:

• Input Voltage Min: 7V 
• Input Voltage Max: 40V 
• DC / DC Converter IC Case: TO-220F 
• No. of Pins: 5Pins 
• Output Current: 3A 
• Output Voltage Nom.: 5V 
• Switching Frequency: 60kHz 
• Topology: Buck (Step Down) 
• Operating Temperature Max: 125°C

Transistor PNP 2N4125

General purpose Transistor PNP 2N4125

• Packaging TO-92
• Type PNP Silicon Transistor
• Max continuous collector current (ic) 200mA
• Maximum collector-emitter voltage (VCE) 30V
• Minimum base-collector voltage of the on-state (VBE) sat 0.95V (@ IC 50 mA, 5.0 mA IB)
• Maximum saturation voltage collector-emitter (VCE) sat 0.4V (@IC 50 mA, 5.0 mA IB)
• hfe 200

Active GPS antenna, MCX connector with cable 5 Meter

Active GPS antenna, MCX connector with cable 5 Meter

External GPS Antenna with Magnet, cable length of 5 meters and uses MCX connectors. Power Supply: 3.0V - 5.0V

Specs:

• Cable Length 5 meters
• Working frequency 1575.42 MHz
• Voltage standing wave ratio (VSWR) 1.5: 1
• The input impedance of 50 Ohm
• ± 30dB Gain

916MHz Helical Antenna HT916

Helical antenna with working frequency 916MHz

W5E-WO-03L WiFi Dipole Antenna and Antenna Cable Assembly

Wiznet W5E-WO-03L WiFi Antenna Dipole Antenna and Cable Assembly

Antenna for 2.4GHz frequency -WiFi / WLAN / Bluetooth / Zigbee with Linear polarization.

Specs:

• Dimensions 102.8 x 11 mm
• The input impedance of 50 Ohm
• Gain +/- 3.5 (dBi)

3dbi Wifi Antenna

Antenna for 2.4GHz frequency (WIFI) black. This antenna has a male SMA connector types, and there is a hinge that can be bent 90 degrees.

Specs:

• Dimensions Height 110mm (straightened)
• The operating frequency of 2.4 GHz / WIFI
• Voltage standing wave ratio (VSWR) 1.5
• The input impedance of 50 Ohm
• Gain 3.0 dBi

EGP50B-E3/54 ultrafast Diode 100V 5Amp

A voltage rectifier has the ability recovery very fast.

• Current of 5 A
• Packaging GP-20
• Input voltage is 100 V peak

IRLZ24N N-Channel Hexfet, Power Mosfet

55V Single N-Channel HEXFET Power MOSFET in a TO-220AB package

• Packaging TO-220-3
• Polarity N-Channel
• Power dissipation 45 W
• Drain-source breakdown voltage 55 V
• Gate-source voltage 16 V
• Continuous drain current 18 A
• Barriers drain-source rds (on) 105 Mohm

AT24C01D-PUM 1Kbit EEprom chip

The Atmel 1Kb 2-wire Serial EEPROM with Full Memory Write Protect, supports up to eight devices on a single 2-wire bus. The EEPROM is organized as 128 words x 8 bits. Optimized for industrial and commercial applications where low-power and low-voltage operations are essential. The EEPROM is available in space-saving packaging options and operates from 1.7V to 3.6V.

Key Parameters

ParameterValue

• Operating Voltage (Vcc): 1.7 to 3.6
• Interface Type: 2-wire
• Density: 1Kb
• Organization: 128 x 8
• Page Size (Bytes): 8
• Temp. Range (deg C): -40 to 85
• Max. Operating Freq. (MHz): 1 MHz
• I/O Pins: 5/8

BTN7971B half bridge motor driver

The BTN7971B is a integrated high current half bridge for motor drive applications. It is part of the NovalithIC™ family containing one p- channel highside MOSFET and one n- channel lowside MOSFET with an integrated driver IC in one package. Due to the p- channel highside switch the need for a charge pump is eliminated thus minimizing EMI. Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with current sense, slew rate adjustment, dead time generation and protection against overtemperature, overvoltage, undervoltage, overcurrent and short circuit. The BTN7971B provides a cost optimized solution for protected high current PWM motor drives with very low board space consumption.

Summary of Features:

• Path resistance of max. 30.5 mΩ @ 150 °C (typ. 16 mΩ @ 25 °C) High Side: max. 12.8 mΩ @ 150 °C (typ. 7 mΩ @ 25 °C) Low Side: max. 17.7 mΩ @ 150 °C (typ. 9 mΩ @ 25 °C)
• Low quiescent current of typ. 7 μA @ 25 °C
• PWM capability of up to 25 kHz combined with active freewheeling
• Enhanced switching speed for reduced switching losses
• Switched mode current limitation for reduced power dissipation in overcurrent
• Current limitation level of 50 A min. / 70 A typ. (low side)
• Status flag diagnosis with current sense capability
• Overtemperature shut down with latch behavior
• Overvoltage lock out
• Undervoltage shut down
• Driver circuit with logic level inputs
• Adjustable slew rates for optimized EMI
• Green Product (RoHS compliant)
• AEC Qualified

Target Applications:

Motor-Drive

AD7705BNZ 2 channel ADC

ADC IC is a 2-channel, 16-bit Sigma-Delta for low frequency measurement applications.

• Power supply 4,75V - 5,25V
• DIP-16 Packaging
• serial interface
• 16 bit resolution
• Number of channels 2

BC546 NPN

BC546 NPN bipolar transistor

• Packaging TO-92
• NPN
• Max continuous collector current (ic) 100 mA
• Minimum base-collector voltage of the on-state (VBE) sat 65 Volt
• hfe 110

Neutrik NP3X Plug Audio TRS 1/4 inch Male

NP3X Neutrik 1/4 inch TRS Audio Plug Male
3 pole professional phone plug from Nuetrik highly suited for audio applications. This plug has contacts made of nickel and is protected by a shield made from nickel.

• Plug terminal type, 3 pole
• Shape (female / male) male
• Pin number 3 pole
• Cable mounting
• Contact Material Nickel
• Packaging materials Nickel

ACR1252U USB NFC Reader III (NFC Forum Certified Reader)

The ACR1252U USB NFC Reader III is an NFC Forum-certified PC-linked reader, developed based on 13.56Mhz contactless technology. It has a SAM (Secure Access Module) slot which can be used together with a SAM card for key diversification and mutual authentication, providing high-level security in contactless transactions. Post-deployment firmware upgrade is also supported, eliminating the need for additional hardware modification.

ACR1252U is capable of the three modes of NFC, namely: card reader/writer, card emulation and peer-to-peer communication. It supports ISO 14443 Type A and B cards, MIFARE®, FeliCa, and ISO 18092–compliant NFC tags. It also supports other NFC devices with an access speed of up to 424 Kbps and proximity operating distance of up to 50mm (depending on tag type used).

Compliant with both CCID and PC/SC, this plug-and-play USB NFC device allows interoperability with different devices and applications. It is thus ideal for unconventional marketing and advertising applications like smart posters.

The ACR1252U comes with an optional stand to hold the smart card reader at an optimal angle, so that users can tap contactless cards or NFC-enabled devices onto the ACR1252U with ease.

Features:

• USB 2.0 Full Speed Interface  
• CCID Compliance  
• USB Firmware Upgradeability  
• Smart Card Reader:  
• Read/write speed up to 424 kbps  
• Built-in antenna for contactless tag access, with card reading distance of up to 50 mm (depending on tag type)  
• Supports ISO 14443 Type A and B cards, MIFARE, FeliCa, and all 4 types of NFC (ISO/IEC 18092) tags  
• Supports MIFARE 7-byte UID, MIFARE Plus and MIFARE DESfire  
• Built-in anti-collision feature (only 1 tag is accessed at any time)  
• One ISO 7816–compliant SAM slot (Class A)  
• NFC Support:  
• NFC Reader/Writer Mode  
• Peer-to-Peer Mode  
• Card Emulation Mode  
• Application Programming Interface:  
• Supports PC/SC  
• Supports CT-API (through wrapper on top of PC/SC)  
• Peripherals:  
• User-controllable bi-color LED  
• User-controllable buzzer  
• SAM Slot

Tech Info:

Dimensions	98.0 mm (L) x 65.0 mm (W) x 12.8 mm (H)
Weight	81.0 g
Interface	USB 2.0 Full Speed
Operating Distance	Up to 50 mm (depends on the tag type)
Supply Voltage	Regulated 5V DC
Supply Current	Max. 200mA
Operating Temperature	0-50 °C
Operating Frequency	13.56 MHz
Smart Card Interface Support	ISO 14443 Type A & B MIFARE FeliCa 4 types of NFC (ISO/IEC 18092) tags
Compliance / Certifications	ISO 18092, ISO 14443, ISO 7816,  NFC Forum, FeliCa Performance Certification, PC/SC, CCID, LASCOM, EN60950/IEC 60950, CE, FCC, VCCI, MIC, KC, RoHS 2, USB Full Speed, Microsoft® WHQL
Operating System Support	Windows® Linux® Mac OS® Android™ 3.1 and above

ACR1252U NFC reader III SDK

Applications:

• e-Government
• Banking & Payment
• e-Healthcare
• Network Security
• Access Control
• e-Purse & Loyalty
• Transportation
• Smart Poster
• P2P Communication

Neutrik NC3FXX 1/4 inch Female XLR Audio Jack

NC3FXX 1/4 inch Neutrik XLR Female Audio Jack

Female XLR connector types NC3FXX of Neutrik. These connectors use the materials for connectors and nickel silver for its protective packaging. This connector is usually used for Audio.

Specs:

• Type XLR terminal
• Shape (female / male) Female
• Pin number 3 pole
• cable mounting
• Contact Material Silver
• Packaging materials Nickel

Neutrik NC3MXX 1/4 inch Male XLR Audio Jack

NC3MXX 1/4 inch Neutrik XLR Male Audio Jack

Male XLR connector types NC3MXX of Neutrik. These connectors use the materials for connectors and nickel silver for its protective packaging. This connector is usually used for Audio.

Specs:

• Type XLR terminal
• Shape (female / male) male
• Pin number 3 pole
• cable mounting
• Contact Material Silver
• Packaging materials Nickel

SMD LED logic tester type B

SMD LED Logic Tester B is a display module for 8 bit parallel port which consists of eight LED SMD configuration with Active Low. Fully compatible with all ports MCS-51 Series Low Cost Low Cost Board and AVR Series Board is configured as an output.

specifications:

- Using the SMD components.

- 8 LED circuit configuration with Active Low.

- Compatible with MCS-51 Series Low Cost Low Cost Board and AVR Series Board.

- Can be used as a display output for program tester.

- Equipment: 1 piece Board SMD LED Logic Tester B, 1 sheet manual.

SMD LED logic tester type A

SMD LED logic tester type A

SMD LED Logic Tester A is a display module for 8 bit parallel port which consists of eight LED SMD configuration with Active Low. Fully compatible with the MCS-51 family MinSys Port1, porta, PortB, and Portc configured as an output.

specifications:

- Using the SMD components.

- 8 LED circuit configuration with Active Low.

- Compatible with MCS-51 MinSys ver 3.0 Board.

- Can be used as a display output for Tesport or TESPPI program.

- Equipment: 1 piece Board SMD LED Logic Tester A and 1 sheet manual.

Simple logic LED tester

Simple logic LED tester

a module consisting of 4 LEDs as output and 4 pieces of tactile switches as input. This module can be used as logic tester for input and output of the microcontroller port.

specifications:

- 4 LED configuration with active low (logic 0 on a port will activate LED).

- 4 tactile switches with active low configuration (tactile switch is pressed will produce a logic 0).

- Can be used on the port PPI (82C55) and port 1 MCS-51 microcontroller.

TDA2003V 10W audio amplifier chip

TDA2003V 10W audio amplifier chip

Audio amplifier with output power of 10W (RL = 2 ohms, f = 1kHz) and frequency response of 40 Hz to 15KHz.

Specs:

• DC power supply 8V - 18V DC
• Output current 3,5A
• packaging Pentawatt
• 40dB closed loop gain bandwidth (f1KHz), 80dB open loop (f1KHz) and 60dB (f10KHz)

Bridge Rectifier RS204-BP 400V/2Amp

Bridge Rectifier with the ability to skip a current of 2A.

• The maximum current 2A
• The maximum input voltage of 400 V

2.8 inch TFT LCD Touch Shield for Arduino

Display module with a size of 2.8 "that is compatible with Arduino.

Features:

- Resolution = 320 x 240.

- Interface standard Arduino (Arduino Uno, Arduino Leonardo, & XNucleo).

- There is a microSD slot, for the purposes of displaying photos.

Specs:

3.3 VDC power supply ?? 5VDC

Dimensions 73,3mm x 55,3mm

Interface SPI (Standard Arduino)

LCD Type TFT LCD (with resistive touch panel)

HX8347D Controller (LCD) & XPT2046 (Touch Screen)

View area 57,6mm x 43,2mm

1N5921B , 6.8 V, 3.0 W Zener Diode Voltage Regulator

This is a complete series of 3.0 Watt Zener Diode Voltage Regulators with tight limits and better operating characteristics that reflect the superior capabilities of silicon-oxide passivated junctions. All this is in an axial-lead, transfer-molded plastic package that offers protection in all common environmental conditions.

• Zener Voltage Range - 3.3 V to 200 V
• ESD Rating of Class 3 (>16 KV) per Human Body Model
• Surge Rating of 98 Watts @ 1 ms
• Maximum Limits Guaranteed On Up To Six Electrical Parameters
• Package No Larger Than the Conventional 1 Watt Package

Mechanical Characteristics:

• CASE: Void free, transfer-molded, thermosetting plastic
• FINISH: All external surfaces are corrosion resistant and leads are readily solderable
• MAXIMUM LEAD TEMPERATURE FOR SOLDERING PURPOSES:230°C, 1/16, from the case for 10 seconds
• POLARITY: Cathode indicated by polarity band
• MOUNTING POSITION: Any
• Pb-Free Packages are Available

H11AA1 Optocoupler, Phototransistor Output, AC Input, with Base Connection

H11AA1 Optocoupler, Phototransistor Output, AC Input, with Base Connection
An output transistor optocoupler (NPN phototransistor).

Widely used in applications:
- Detection of telephone line.
- AC line motors.
- PLC.
- Intrumentasi.

Features
AC or polarity insensitive input
Built-in reverse polarity input protection
I/O compatible with integrated circuits

General Specs:
Emitter voltage of 30 V (max)
Component output (transistor / triac) transistor
5300 Vrms isolation voltage
DIP-6 Packaging

TDA8950TH/N1 Audio Power Amplifier

NXP  TDA8950TH/N1  Audio Power Amplifier, D, 2 Channel, 150 W, ± 12.5V to ± 40V, HSSOP, 24 Pins

The TDA8950TH/N1 is a high efficiency, two channel class D audio power amplifier in 24 pin HSOP package. The typical output power is 2 x 150W with speaker load impedance of 4ohm. For each channel, the audio input signal is converted into a digital PWM signal using an analogue input stage and PWM modulator. The TDA8950TH/N1 contains high power switches, drivers, timing and handshaking between power switches along with some control logic. To ensure maximum system robustness, an advanced protection strategy has been implemented to provide overvoltage, overtemperature and overcurrent protection. Each of the two audio channels contains PWM modulator, analogue feedback loop and differential input stage.

• Symmetrical operating supply voltage range from ±12.5V to ±40V
• Low quiescent current consumption of 50mA
• Stereo full differential inputs, can be used as stereo SE or mono BTL amplifier
• Thermal foldback (TFB)
• Smooth pop noise free start up and switch off
• Zero dead time switching
• Fixed gain of 30dB in SE and 36dB in BTL applications
• BD modulation in BTL configuration
• Fully short circuit proof across load
• Ambient temperature range from -40°C to 85°C

Sanfix 32 in 1 screwdriver set

SANFIX 32 in 1 screwdriver set

* PH0 - SL0-1
* PH1 - SL3-4
* PH2 - SL5-6
* PH3 - SL8-10
* HEX2mm - HEX2.5mm
* HEX3mm - HEX4mm
* HEX5mm - HEX6mm
* SR0 - SR1
* SR2 - SR3
* T5 - T30
* T6 - T40
* T10 - T15
* T20 - T25
* TH10 - TH20
* PZ1 - PZ2
* PZ0 - PZ3

OEM Switching Power Supply 12V / 5Amp

OEM Switching Power Supply 12V / 5Amp

features:

- AC to DC Power supply

- A wide input voltage range

- Small size, light weight, high efficiency

- Protection features: short circuit / overload

- Air cooling

- LED indicator

- 100% of full load testing

- Size: 244 x 137 x 70 (mm)

Technical parameters:

- Output voltage: 12 V

- Flow Output: 5A

- Output Power: 60 W

- Input Voltage: 85-230 VAC

- Input Freq: 47-63 Hz

- Output adjustment range: ± 10%

- Overload Protection: 105% -200%, automatically revived

- Over voltage protection: 115% -135%

- Short-circuit protection: automatic life kembal

- Time start output: <= 2 seconds @ 120VAC, <= 1 sec @ 230VAC

- Time keeping output:> = 10 milli-seconds @ 120 VAC,> = 20 milli-seconds @ 230 VAC

- Exodus dielectric:

Input-output: AC1500V, 1 minute

Input-chassis: AC1500, 1 minute

Input-chassis: DC500V, 1 minute

- Work environment: -10 ° C to 50 ° C, 20% -90% RH (no condensation)

- Safety standards: reference design EN / UL60950

- Electromagnetic compatibility standards: EN55022 Class B reference design

HKE HRS2H-S 24VDC DPDT Relay

Relay 24VDC with configuration DPDT (double-pole, double-throw) brand HKE.

• Coil sensivity: 200mW
• Number of pins 8 Pin
• Dimensions 20.3 x 9.9 x 11.4 mm
• configuration DPDT
• Coil voltage 24VDC
• Contact voltage 120VAC / 24VDC
• Contact Flow 1A

June 2016 Single Board Computer Comparison

Do you want to buy a new single board computer to start building new things? Before doing that, go ahead and take a look at the ultimate hacker board comparison chart that tells you the major features and price of these Single Board Computers.

Raspberry Pi and Arduino are well-recognized single board computers, there are tons of other boards available if you want to start making new things and hacking.

Product	Price ($)	Vendor	Processor	Cores
86Duino Zero	39	DMP	Vortex86EX	1x x86 @ 300MHz
A20-OlinuXino-Lime	37	Olimex	Allwinner A20	2x A7 @ 1GHz
A20-OlinuXino-Lime2-EMMC	61	Olimex	Allwinner A20	2x A7 @ 1GHz
A20-OlinuXino-Micro	61	Olimex	Allwinner A20	2x A7 @ 1GHz
Andromeda Box Edge	75	Marvell, Arrow	Marvell IAP140	4x A53 @ 1.2GHz
Arduino Industrial 101	39	Arduino Srl	Qualcomm AR9331 1x MIPS @ 400MHz
Arduino Yún Mini	60	Arduino Srl	Qualcomm AR9331 1x MIPS @ 400MHz
Arduino Tian	99	Arduino Srl	Qualcomm AR9432 1x MIPS @ 560MHz
			Samsung Exynos	4x A15 @ 1.8GHz +
Arndale Octa	199	InSignal, Pyrustek	5420	4x A7 @ 1.3GHz
Banana Pi M2	58	SinoVoip	Allwinner A31	4x A7 @ 1GHz
Banana Pi M2+	37	SinoVoip	Allwinner H3	4x A7 @ 1.6GHz
Banana Pi M3	70	SinoVoip	Allwinner A83T	8x A7 @ 2GHz
Banana Pro	48	LeMaker	Allwinner A20	2x A7 @ 1GHz
BeagleBone Black	48	BeagleBoard.org	TI Sitara AM3358	1x A8 @ 1GHz
BeagleBone Green	39	SeeedStudio	TI Sitara AM3358	1x A8 @ 1GHz
BeagleBone Green Wireless	45	SeeedStudio	TI Sitara AM3358	1x A8 @ 1GHz
Bubblegum-96	89	uCRobotics	Actions S900	4x A53 @ 1.8GHz
Chip	9	Next Thing	Allwinner R8	1x A8 @ 1GHz
				1x ARM9 @
CloudBit	60	LittleBits	Freescale i.MX233	454MHz
Creator CI40	156	Imagination Tech. Imagination CXT200		2x MIPS @ 550MHz
Cubieboard3	86	Cubieboard.org	Allwinner A20	2x A7 @ 1GHz
				4x A15 @ 2GHz +
Cubieboard4	125	Cubieboard.org	Allwinner A80	4x A7 @ 1.3GHz
Cubieboard5	99	Cubieboard.org	Allwinner H8	8x A7 @ 2GHz
DPT-Board	56	DPTechnics	Qualcomm AR9331 1x MIPS @ 400MHz
			Qualcomm
DragonBoard 410c	75	Qualcomm, Arrow	Snapdragon 410	4x A53 @ 1.2GHz
Firefly FirePrime	99	Firefly	Rockchip RK3128	4x A7 @ 1.3GHz
Firefly-RK3288	159	Firefly	Rockchip RK3288	4x A17 @ 1.8GHz
Firefly-RK3288 Reload	189	Firefly	Rockchip RK3288	4x A17 @ 1.8GHz
Galileo Gen 2	56	Intel	Intel Quark X1000	1x x86 @ 400MHz
		AMD,	AMD G-Series
Gizmo 2	189	GizmoSphere	GX210HA	2x x86 @ 1GHz
	75 (99 with	LeMaker,
HiKey	2GB)	96Boards.org	HiSilicon Kirin 6220	8x A53 @ 1.2GHz
HobbitBoard	69	Wandboard.org	NXP I.MX6 UL	1x A7 @ 528MHz
	70 (with			1x/2x/4x A9 @ up to
HummingBoard-Base	Solo)	SolidRun	NXP i.MX6	1.2GHz

	85 (with			1x/2x/4x A9 @ up to
HummingBoard-Pro	Solo)	SolidRun	NXP i.MX6	1.2GHz
	102 (with			1x/2x/4x ARM @ up
HummingBoard-Edge	Solo)	SolidRun	NXP i.MX6	to 1.2GHz
	70 (with			1x/2x/4x ARM @ up
HummingBoard-Gate	Solo)	SolidRun	NXP i.MX6	to 1.2GHz
			Qualcomm
Inforce 6410Plus	143	Inforce	Snapdragon 600	4x A15 @ 1.7GHz
				2x x86 @ 500MHz +
Intel Edison Kit for Arduino	87	Intel	Intel "Tangier" Atom	Quark
LeMaker Guitar	45	LeMaker	Actions S500	4x A9 @ 1.6GHz
		SeeedStudio,	MediaTek
LinkIt Smart 7688	13	MediaTek	MT7688AN	1x MIPS @ 580MHz
LinkSprite Acadia V3	119	LinkSprite	NXP i.MX6 Quad	4x A9 @ 1.2GHz
				4x A15 @ 2GHz +
LinkSprite Arches	95	LinkSprite	Allwinner A80	4x A7 @ 1.3GHz
		HaoYu,
MarsBoard AM335x	75	MarsBoard.org	TI AM3358	1x A8 @ 1GHz
		HaoYu,
MarsBoard RK3066	58	MarsBoard.org	Rockchip RK3066	2x A9 @ 1.6GHz
		HaoYu,
MarsBoard RK3066 Pro	140	MarsBoard.org	Rockchip RK3066	2x A9 @ 1.6GHz
		Intel, ADI,
MinnowBoard Max Turbot	140	Minnowboard.org	Intel Atom E3826	2x x86 @ 1.46GHz
NanoPC-T3	60	FriendlyARM	Samsung S5P6818	8x A53 @ 1.4GHz
NanoPi M1	11	FriendlyARM	Allwinner H3	4x A7 @ 1.2GHz
NanoPi M2	25	FriendlyARM	Samsung S5P4418	4x A9 @ 1.4GHz
NanoPi M3	35	FriendlyARM	Samsung S5P6818	8x A53 @ 1.4GHz
NanoPi2 Fire	23	FriendlyARM	Samsung S5P4418	4x A9 @ 1.4GHz
Odroid-C0	27	Hardkernel	Amlogic S805	4x A5 @ 1.5GHz
Odroid-C1+	32	Hardkernel	Amlogic S805	4x A5 @ 1.5GHz
Odroid-C2	40	Hardkernel	Amlogic S905	4x A53 @ 2GHz
			Samsung	4x A15 @ 2GHz +
Odroid-XU4	74	Hardkernel	Exynos5422	4x A7 @1.4GHz
Orange Pi Lite	12	Shenzhen Xunlong	Allwinner H3	4x A7 @ 1.2GHz
Orange Pi One	10	Shenzhen Xunlong	Allwinner H3	4x A7 @ 1.2GHz
Orange Pi PC / PC Plus	15	Shenzhen Xunlong	Allwinner H3	4x A7 @ 1.6GHz
Orange Pi Plus2 / Pluse2E	49	Shenzhen Xunlong	Allwinner H3	4x A7 @ 1.6GHz)
			Zilinx Zynq-	2x A7 @ 667MHz +
Parallella	99	Adapteva	7020/7010	FPGA
pcDuino Lite / Lite WiFi	29	LinkSprite	Allwinner A10	1x A8 @ 1GHz
pcDuino3 Nano / Nano Lite	40	LinkSprite	Allwinner A20	2x A7 @ 1GHz
pcDuino8 Uno	49	LinkSprite	Allwinner H8	8x A7 @ 2GHz
Pine A64	15	Pine64	Allwinner A64	4x A53 @ 1.2GHz
PixiePro	100	Code	NXP i.MX6 Quad	4x A9 @ 1GHz
Radxa Rock Lite / Rock Pro	59	Radxa	Rockchip RK3188	4x A9 @ 1.6GHz
Radxa Rock 2 Square	129	Radxa	Rockchip RK3288	4x A17 @ 1.6GHz
			Broadcom
Raspberry Pi Zero	14	Rpi Trading	BCM2835	1x A8 @ 1GHz

Raspberry Pi 2 Model B	35	Rpi Trading	BCM2836	4x A7 @ 900MHz
			Broadcom
Raspberry Pi 3 Model B	35	Rpi Trading	BCM43437	4x A53 @ 1.2GHz
Rico Board	99	MYIR	TI AM437x	1x A9 @ 1GHz
		Newark,
RioTboard	79	RioTboard.org	NXP i.MX6 Solo	1x A9 @ 1GHz
Roseapple Pi	50	Roseapplepi.org	Actions S500	4x A9 @ 1.6GHz
SAMA5D4 Xplained	94	Newark, Atmel	Atmel SAMA5D4	1x A5 @ 528MHz
Seeeduino Cloud	70	SeeedStudio	Qualcomm AR9331 1x MIPS @ 400MHz
			Xilinx Zynq-	2x A9 @ 667MHz +
Snickerdoodle	62	Krtkl	7010/7020	FPGA
Udoo Neo	50	Udoo (Seco)	NXP i.MX6 SoloX	1x A9 @ 1GHz)
			NXP i.MX6
Udoo Quad/Dual/Dual Basic	99	Udoo (Seco)	Dual/Quad	2x/4x A9 @ 1GHz
USB Armory	130	Inverse Path	NXP i.MX53	1x A8 @ 800MHz
				1x, 2x, or 4x A9
Wandboard	79	Wandboard.org	NXP i.MX6	@1GHz
			Xilinx Zynq-	2x ARM @ 667MHz
Z-turn Board	99	MYIR	7010/7020	+ FPGA

Download Complete PDF file here