EMS Logger Pi Shield

 Raspberry Pi add-on  Module for recording purposes (data logger). Equipped with 2-channel ADC, 2 channel DAC with a resolution of 12 bits, and Real Time Clock so that the module can be connected to the sensor easily. The application of this module include: recording sensor data as temperature, air pressure, gas sensors, and others.

specifications:

- It has two 12-bit ADC channels based MCP3202 IC with 5 volt reference voltage.

- It has two 12-bit DAC channel based IC MCP4922 with 5 volt reference voltage.

- Have a DS1307 RTC IC-based, with 56 bytes of NV SRAM and battery backup 3Volt.

- Equipped with a hex buffers / drivers SN74LVC07-based, so the module can be connected directly to the I / O in the header Raspberry Pi®.

- Using the I2C interface for RTC and SPI interface to the ADC-DAC.

- ADC Input Range: 0-5 Volts.

- DAC output Range: 0-5 Volts.

- Using the power source of Raspberry Pi®.

- Compatible with Raspberry Pi® type A, type B, and type B +.

Arduino Jumper Cables

Colorful jumper cables for use in breadboard. Available in 1 pack 4 sizes: 200mm, 165mm, 125mm and 80mm.

Digital Tilt Sensor for Arduino V2

This product is a digital tilt sensor is compatible with the Arduino products. This module can be easily connected to the I / O expansion board or sensors.

specifications:

- Power supply: 3.3V - 5V

- Interface: Digital

- Size: 22x30 (mm)

Line Tracking Sensor for Arduino

The sensor module is a very basic function, in which a robot can move precisely follow the path that we have set.

specifications:

- Power supply: 3.3V - 5V

- Interface: Digital

- Current: 20 mA @ 5V

- Temperature: 0 ° C + 50 ° C

- Output: TTL (for Low Output Black and White for High Output)

- Size: 28x10 (mm)

ISD1700 Series Starter Kit

This module uses the chip ISD17240 from Nuvoton to record and play back audio signals during 8 minutes. This module can be operated automatically or controlled by the controller.

A wide variety of applications of this module are: audio ads, toys, robot, announcer (announcement) automatically.

specifications:

- Based IC recorder ISD17240PYI.

- Available connectors to connect to speakers or AUX output.

- Condenser Mic Input sound using the module or through the LINE IN connector.

- Equipped with tactile switches to control Vol, Play, Rec, Erase, Fwd, FT, and Reset.

- Comes with 2 pieces of LED as an indicator of the operating status of the module.

- There is also a connector for interface pad in SPI or parallel to the microcontroller.

- Requires power supply of 2.4 s / d 5.5 VDC.

BITalino Plugged Kit

BITALINO IS SHIPPED WITH THE SENSORS (ECG, EMG, EDA, ACCELEROMETER, LIGHT, LED) SNAPPED OFF FOR YOU, AND WE ADD RJ22 PLUGS TO YOUR BITALINO SO YOU CAN USE THE SENSORS INTERCHANGEABLY OR CONNECT YOUR OWN DESIGNS.

This kit includes:

1x BITalino hardware (MCU, Bluetooth, Power, ECG, EMG, EDA, Accelerometer, Light, LED) with already snapped sensors

1x 3-lead accessory (for EMG / ECG)

1x 2-lead accessory (for EDA)

5x Pre-gelled electrodes

1x Li-Po Battery 320mAh

1x RJ22 to Molex Sherlock sensor connection cable (1m length)

BlueTank App Kit

BlueTank App Kit is a set of tangible module robot tank that can be controlled by Android  gadgets via Bluetooth®.

equipment:

• 1 AVR Leoduino.
• 1 EMS Blue Shield.
• 1 Robot Tank Shield.
• 1 Battery Shield.

Dimensions: 16.2 cm  x 10.75 cm x 8.2 cm

Battery Shield

Battery Shield is a shield with a voltage source 7,4VDC Lithium Polymer battery. Shield is compatible with Inoduino , Arduino Leonardo , Leoduino, Arduino Uno , Unoduino, and Arduino  Mega , Maxiduino. This module can be used in applications that require portability or a robot.

Leoduino with clear acrylic case

Leoduino is module-based single-chip microcontroller ATmega32U4 and compatible with Arduino Leonardo. This module has been equipped with a bootloader so it does not require additional tools for programming. By utilizing the bootloader in the Leoduino, users can communicate with computers and programming via the USB.

more info:

• http://2r-he.blogspot.com/2013/06/leoduino-arduino-leonardo-compatible.html
• http://2r-he.blogspot.com/2014/04/leoduino-case.html

OLIMEXINO-85-ASM

THE SMALLEST OLIMEX ARDUINO-INSPIRED BOARD

The board comes ready-to-use! OLIMEXINO-85 is a very tiny - (32x20)mm - Arduino-inspired board. It is built around the well-known Little wire design. The same design is also used for the Digispark and Adafruit’s Trinket. The microcontroller comes preprogrammed with "micronucleus tiny85" that is suitable for use with the Digispark's Arduino distribution.

FEATURES

• ATtiny85-PU microcontroller with pre-loaded "micronucleus tiny85" bootloader
• Tested and working out-of-the-box with Digisparks's Arduino distribution
• Breadbord compatible via the header
• Two LEDs - power and status
• Reset button
• All components already soldered (unlike the DIY version)
• Easy-to-replace components in case of a fault
• Open-hardware board, board schematics and layout available for Eagle
• Open-software board, thanks to the Digispark's community effort
• Dimensions - (1.275 x 0.800)'' ~ (32 x 20)mm

OLIMEXINO-NANO

OPEN SOURCE HARDWARE WEARABLE ARDUINO LEONARDO-LIKE DEVELOPMENT BOARD

FEATURES

• ATMEGA32U4 Arduino Leonardo compatible
• Works with Arduino IDE
• Micro USB cable connector (unlike most of the other Olimex boards which use mini USB)
• User button
• Reset button
• Micro SD card connector
• Two stackable connectors
• UEXT connector for connection to OLIMEX UEXT modules
• Intelligent power supply can take power from USB or external LiPo battery (OLIMEXINO-BAT module)
• Ultra low power design for battery and handheld operations

A20-SOM-EVB

REFERENCE DESIGN FOR A20-SOM ON 2 LAYER BOARD
A20-SOM-EVB is reference design on 2 layer board for A20-SOM which adds VGA, HDMI, Audio In/Out, LCD, 2 Mpix Camera, Gigabit Ethernet, SATA, USB-OTG and 2 USB hosts is available with Eagle CAD files, so everyone can modify and tailor to his needs.

FEATURES

• Includes A20-SOM-4GB
• A20-SOM(-4GB) matching connectors
• VGA output with a connector
• HDMI output with a connector
• LCD output on a row-of-pins
• Gigabit interface with a connector
• Camera 2 Mpix
• 2xUEXT connectors
• SATA connector and SATA power connector
• USB-OTG with power control and current limiter
• LiPo Battery connector with battery-charging capabilities
• Mic input and headphones out with connectors
• Android 7 buttons
• SD-MMC connector
• UART0 connector for console debug
• 5 GPIO connectors x40 pin 0.1"
• Status LEDs
• 4 x M3 x 8mm screws and 4 x M3 x 6mm metal spacers
• Dimensions of the SOM part: (3200 x 2200)mil ~ (55.88 x 81.28)mm
• Dimensions of the EVB part: (5300 x 4050)mil ~ (134.62 x 102.87)mm

AD-102 Breadboard

This breadboard will allow prototyping of projects prior to a more permanent assembly solution, it's ideal for hobbyists, students, Lab work or by any one who needs to test a circuit. A self-adhesive pad is attached to the rear of the breadboard.Can also be connected to AD-01(BZ13P), AD-100(AG08J), AD-101(AG09K), or other AD-102 blocks. Dimensions: 62x83x10mm.

AD-11 Solderless Breadboard

AD-11 Solderless Breadboard

A range of solderless breadboard modules that can interconnect to suit individual requirements. The basic board AD-01 consists of four blocks of six columns of 28 rows, the sockets in each row being interconnected. The blocks are a standard DIP size apart, although MSI and LSI type chips can be used. At both ends of the blocks, there are two power busses. The ‘Red’ bus is made up of two separate rows of 12 connecting sockets, and the ‘Black’ bus is one row of 24 connecting sockets.

There is an additional matrix of 30 by 6 sockets for non-dip type components. The six sockets in the vertical plane are interconnected. Each socket will accept solid wire from 20 to 30 swg (0•3 to 0•8mm). The base has a ‘sticky’ covering to hold the board firm on a workbench or surface. The AD-10 power block has 5 individual screw terminals that will accept 4•5mm Y-terminal, stripped wire or 4mm banana plug. Each terminal is connected to two sockets. The power block will snap lock onto the AD-01 base board to allow connections to the required power bus. The power block has the same ‘sticky’ base. After use the modules can be unlocked and remade into a different configuration.

AD-11 is one AD-01 and one AD-10. Size: 147 x 80mm

GL-24 by KandH Breadboard-1680 Tie Points

The GL-24 is a 1680 tie point solderless breadboard with a rigid ABS plastic backplate.

KS-350 Jump Wire Kit by KandH

Jump Wire KandH production. Suitable for use as a jumper on the breadboard.

specifications:
- # 22 AWG solid wire
- Pre-cut, pre-stripped, Pre-formed
- There are a wide variety of cable lengths
- Packaging: 270 x 124 x 30 mm

SFP CWDM-1.25G-80D-XX by 6COM

Specs:

• Brand Name 6COM
• Model Number CWDM-1.25G-80D-xx
• Data Rate 1.25G
• Wavelenth 1470-1610
• Distance 80km
• Package CWDM SFP
• Temperature 0-70
• DDMI yes
• Connecter lc
• Source DFB+PIN

Features:

• Data-rate of 1.25Gbps operation
• 18 CWDM DFB wavelengths laser and PIN photodetector for 80km transmission
• Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
• Digital Diagnostic Monitoring:
• Internal Calibration or External Calibration
• Compatible with SONET OC-24-LR-1
• Compatible with RoHS
• +3.3V single power supply
• Operating case temperature:
• Standard : 0 to +70°C

Applications:

• Gigabit Ethernet
• Fiber Channel
• Switch to Switch interface
• Switched backplane applications
• Router/Server interface
• Other optical transmission systems

Schmart Board P8X32A-Q44

Propeller microcontroller development board based P8X32A of parallax. This board has a 32-pin I / O, 8 resistive touch buttons, and 8 LEDs buffer. There are 3 types of interfaces that can be used on this board, namely: 3.3V Serial USART, I2C, and USB. In addition, some of the interesting features of this board is a built-in serial EEPROM and Delta Sigma Digital to Analog Converter which can be used for storage or processing of data. In terms of programming, you can download the program on this board with a micro USB cable and Propeller Tool software on the PC.

Specs:

• The power supply is 3.3V or 4-9V DC
• Features touch buttons, LEDs, serial EEPROM, Delta Sigma DAC
• Dimensions 5.0 x 7.6 x 0.84 cm
• Based microcontroller / microprocessor Propeller P8X32A
• Number of port i / o 32 I / O
• Port USB interface, 3.3V USART, I2C
• bootloader -
• Micro USB programming port

Development board OM11049

OM11049 development board is a board with a 32bit processor NXP LPC1114 ARM Cortex-M0. This board has a high-performance (50MHz), low power consumption (130μA / MHz) and the ability to reduce power by 60% in sleep mode. OM11049 programming can be done with LPCXpresso IDE using C language.

Specs:

• 3.3 VDC power supply or 5.0V DC from USB
• Features LPC1114 MCU, integrated JTAG debugger, In-system / application programing
• Dimensions 34.29 x 138.43 mm
• Based microcontroller / microprocessor ARM Cortex-M0 LPC1114
• Number of port i / o 48
• LPC-Link interface port, I2C, SPI
• bootloader None
• Port programming LPC-Link On-board (with 10 pin JTAG header)

Arduino Pro Mini 328 - 5V/16MHz

 This is a 5V Arduino running the 16MHz bootloader. Arduino Pro Mini does not come with connectors populated so that you can solder in any connector or wire with any orientation you need. We recommend first time Arduino users start with the Uno R3. It’s a great board that will get you up and running quickly. The Arduino Pro series is meant for users that understand the limitations of system voltage (5V), lack of connectors, and USB off board.

 In order to accomplish this we used all SMD components, made it two layer, etc. This board connects directly to the FTDI Basic Breakout board and supports auto-reset. The Arduino Pro Mini also works with the FTDI cable but the FTDI cable does not bring out the DTR pin so the auto-reset feature will not work. There is a voltage regulator on board so it can accept voltage up to 12VDC. If you’re supplying unregulated power to the board, be sure to connect to the “RAW” pin and not VCC.

The latest and greatest version of this board breaks out the ADC6 and ADC7 pins as well as adds footprints for optional I2C pull-up resistors.

Features:

• ATmega328 running at 16MHz with external resonator (0.5% tolerance)
• 0.8mm Thin PCB
• USB connection off board
• Supports auto-reset
• 5V regulator
• Max 150mA output
• Over current protected
• Weighs less than 2 grams!
• DC input 5V up to 12V
• On board Power and Status LEDs
• Analog Pins: 8
• Digital I/Os: 14
• Dimensions: 0.7x1.3" (18x33mm)

Magnetic Switch

3 terminal (SPDT) Magnetic switch , normally open & normally close

PCH-105D2H Relay SPDT 5VDC 5A

5 VDC Relay configuration with single pole double throw (SPDT)

Specs:

• Pin number 5
• Dimensions 20 x 10 x 15.2 mm
• SPDT configuration
• Coil voltage 5 V
• Coil currents of 80 mA
• Contact Voltage 30 VDC / 277 VAC
• Contact currents 5 A

Parallax RLY-MECH, SPDT, 12A, 12VDC

12 Amp /12 V Relay with a single pole double throw configuration (SPDT) Parallax production.

A10-OLinuXino-LIME

OPEN SOURCE HARDWARE EMBEDDED ARM LINUX SINGLE BOARD COMPUTER WITH ALLWINNER A10 CORTEX-A8

FEATURES

• Allwinner A10 Cortex-A8 processor typically running at 1GHz and Mali 400 GPU
• 512MB DDR3 RAM memory
• SATA connector with 5V SATA power jack
• HDMI connector with FullHD support (1080p)
• 2 x USB High-speed host with power control and current limiter
• USB-OTG with power control and current limiter
• 100MBit native Ethernet
• LiPo Battery connector with battery-charging capabilities
• LCD row of pins (0.05'' step)
• 160 GPIOs on four GPIO rows of pins (0.05'' step)
• MicroSD card connector
• DEBUG-UART connector for console debug with USB-SERIAL-CABLE-F
• GPIO LED
• Battery charge status LED
• Power LED
• 2KB EEPROM for MAC address storage and more
• 3 BUTTONS with ANDROID functionality + RESET button
• 4 mount holes
• 5V input power supply, noise immune design
• PCB dimensions: 84x60 mm

A20-OLinuXIno-LIME2

OPEN SOURCE HARDWARE EMBEDDED ARM LINUX SINGLE BOARD COMPUTER WITH ALLWINNER A20 DUAL CORE CORTEX-A7 1GB RAM AND GIGABIT ETHERNET

FEATURES

• Allwinner A20 dual core Cortex-A7 processor, each core typically running at 1GHz and dual-core Mali 400 GPU
• 1GB DDR3 RAM memory
• SATA connector with 5V SATA power jack
• HDMI connector with FullHD support (1080p)
• 2 x USB High-speed host with power control and current limiter
• USB-OTG with power control and current limiter
• 1000MBit native Ethernet
• LiPo Battery connector with battery-charging capabilities
• LCD row of pins (0.05'' step)
• 160 GPIOs on four GPIO rows of pins (0.05'' step)
• MicroSD card connector
• DEBUG-UART connector for console debug with USB-SERIAL-CABLE-F
• GPIO LED
• Battery charge status LED
• Power LED
• 2KB EEPROM for MAC address storage and more
• 3 BUTTONS with ANDROID functionality + RESET button
• 4 mount holes
• 5V input power supply, noise immune design
• PCB dimensions: 84x60 mm

A20-OLinuXino-LIME

OPEN SOURCE HARDWARE EMBEDDED ARM LINUX SINGLE BOARD COMPUTER WITH ALLWINNER A20 DUAL CORE CORTEX-A7

A20-OLinuXino-LIME is a very compact (84x60)mm Linux open source hardware computer.

FEATURES

• Allwinner A20 dual core Cortex-A7 processor, each core typically running at 1GHz and dual-core Mali 400 GPU
• 512MB DDR3 RAM memory
• SATA connector with 5V SATA power jack
• HDMI connector with FullHD support (1080p)
• 2 x USB High-speed host with power control and current limiter
• USB-OTG with power control and current limiter
• 100MBit native Ethernet
• LiPo Battery connector with battery-charging capabilities
• LCD connector compatible with with 4.3", 7.0", 10.1" LCD modules from Olimex
• 160 GPIOs on four GPIO connectors
• MicroSD card connector
• DEBUG-UART connector for console debug with USB-SERIAL-CABLE-F
• GPIO LED
• Battery charge status LED
• Power LED
• 2KB EEPROM for MAC address storage and more
• 3 BUTTONS with ANDROID functionality + RESET button
• 4 mount holes
• 5V input power supply, noise immune design
• PCB dimensions: 84 x 60 mm

iButton MICRO CAN DS1990A-F5

IButton data storage module that is capable of performing 64-bit encryption of the data to be stored.

specifications:
- Power supply: 2.8 ?? 6.0 V.
- 1-wire interface.
- 64-bit registration number (lasered / ROM).
- Read time: <5 ms.="" p="">- Package: MicoCAN F5 iButton.
- Application: Can be used for storage of ID as access control, guard tour or data logger application.
- Requires device as a media reader to read or write the data (DS9092)

What Is an iButton Device?

The iButton® device is a computer chip enclosed in a 16mm thick stainless steel can. Because of this unique and durable container, up-to-date information can travel with a person or object anywhere they go. The steel iButton device can be mounted virtually anywhere because it is rugged enough to withstand harsh environments, indoors or outdoors. It is small and portable enough to attach to a key fob, ring, watch, or other personal items, and be used daily for applications such as access control to buildings and computers, asset management, and various data logging tasks.

What Can I Do with the iButton Device?

The iButton device is ideal for any application where information needs to travel with a person or object. Affixed to a key fob, watch, or ring, an iButton device can grant its owner access to a building, a PC, a piece of equipment, or a vehicle. Attached to a work tote, it can measure processes to improve efficiency, such as manufacturing, delivery, and maintenance. Some iButton devices can be used to store electronic cash for small transactions, such as transit systems, parking meters, and vending machines. The iButton device can also be used as an electronic asset tag to store information needed to keep track of valuable capital equipment.

DS9092L iButton Probe with LED

The DS9092L iButton® probe with LED provides the electrical contact necessary for the transfer of data to and from the DS19xx family of iButtons. The round probe shape provides a self-aligning interface that readily matches the circular rim of the iButton's MicroCan™ package. The solid metal contacts resist wear and are easy to keep clean.

The DS9092L has no moving parts, making it a rugged interface for harsh environments. The round center contact of the DS9092L houses the LED that is rated for maximum 20mA DC at 2.7V typical.

The probe comes with a brass M18 x 1 nut for panel mounting. Since the body of the probe also forms the ground contact, the panel should be of non-conducting material to avoid ground loops. The 30cm cable with connector is provided for easy connection to the system microcontroller.

Key Features

• Solid metal read/write panel-mount probe for the iButton family
• Integrated green LED for user-feedback signaling
• Probe guides the entry of the iButton
• iButton slides over the surface to self-clean contacts
• Accessible shallow probe cavity simplifies removal of debris such as mud
• Probe suited for panels of up to 3mm thickness
• Contacts are made from solid 303 stainless steel with a blue nylon insulation
• Metric design, prewired for easy installation

DEKKO UT330 Ultrasonic Thickness Gauge

DEKKO UT330 Ultrasonic Thickness Gauge

Features:

• Auto Calibration to assure accuracy
• Auto linear compensation
• Quick adjustment
• Coupling status indication
• 10 thickness measuring storage, and recall function
• 12 sound velocity for different material
• Low battery indication
• More than 10, 000 time long lift key
• Special memory that retains all of its setting even when the power is off

Specification :

• Display : 4 digital LCD
• Minimum Display : 0.1 mm
• Work Frekuency : 5 Mhz
• Measuring Range : 1.2mm to 300.0 mm on steel
• Minimum Limit tube measuring : ¦ 20 x 3 mm steel
• Accuracy : ± 1% + 0.1mm
• Sound velocity range : 1, 000 to 9, 900 m/ s
• Operating temperature : 0º C to 40º C
• Power Supply : 3 x 1.5Volt AAA Battery
• Size : 70.0 x 145.5 x 28mm

DEKKO 230 Ultrasonic Thickness Gauge

DEKKO 230 Ultrasonic Thickness Gauge

Features:

• Auto Calibration to assure accuracy
• Auto linear compensation
• Quick adjustment
• Coupling status indication
• 10 thickness measuring storage, and recall function
• 12 sound velocity for different material
• Low battery indication
• More than 10, 000 time long lift key
• Special memory that retains all of its setting even when the power is off

Specification :
Display : 4 digital LCD
Minimum Display : 0.1 mm
Work Frekwency : 5 Mhz
Measuring Range : 1.2mm to 225.0 mm on steel
Minimum Limit tube measuring : ¦ 20 x 3 mm steel
Accuracy : ± 1% + 0.1mm
Sound velocity range : 1, 000 to 9, 900 m/ s
Operating temperature : 0º C to 40º C
Power Supply : 3 x 1.5Volt AAA Battery
Size : 70.0 x 145.5 x 28mm

DEKKO MT160 Ultrasonic Thickness Gauge

DEKKO MT-160 Ultrasonic Thickness Gauge

Overview

• Capable of performing measurements on a wide range of material
• Including metals
• Plastic
• Ceramics
• Composites
• Epoxies
• Glass and other ultrasonic wave well-conductive materials

Specification

• Display : 4.5 digits LCD with EL backlight.
• Measuring Range : 0.75^ 300mm ( in Steel) .
• Sound Velocity Range : 1000~ 9999 m/ s.
• MT160 : 0.1/ 0.01mm
• Accuracy : ± 0.5% Thickness + 0.04mm, depends on materials and conditions
• Units: Metric/ Imperial unit selectable.
• Four measurements readings per second for single point measurement, and ten per second for Scan Mode.
• Memory for up to : 20 files ( up to 99 values for each file) of stored values.
• Power Source : Two “ AA” size, 1.5 Volt alkaline batteries. 100 hours typical operating time ( EL backlight off) .
• Communication : RS232 serial port.
• Outline dimensions : 150× 74× 32 mm.
• Weight : 245g

NuEdu-SDK-NUC240

Development Board for NUC240 microcontroller (ARM Cortex M0). This board is suitable for the manufacture of products in the prototype that uses a microcontroller NUC240. This board has been integrated with Nu-Link ME module for charging process program code via ICP. About the programming language / compiler, this board can be programmed using the C programming language with the help of software EWARM IAR, Keil RVMDK, or CooCox CoIDE. This board is also equipped with a header that is compatible with the Arduino making it easier to connect with various Arduino shield.

specifications:

- Power supply: 5VDC

- Integrated with microcontroller NUC240.

- Have a Programmer / Debugger internal (Nu-Link-Me).

- Completion of the program code can be via USB ICP (Nu-Link-Me).

- Sales Package: 1x NuEdu-SDK-NUC472, 1x NuEdu-Basic 01, Nu-Bridge 1x, 1x USB cable and 1x CD manual

NuEdu-SDK-NUC472

NuEdu-SDK-NUC472 a microcontroller development board for NUC472. Users can use NuEdu-EVB-NUC472 to develop and test the application program with ease.

specifications:

-Catu Power: 5VDC

-based Microcontroller / microprocessor NUC472 (ARM Cortex-M4)

-Support EWARM IAR or Keil RVMDK

-Have A header that is compatible with the Arduino so that it can be connected to an Arduino shield

-Terintegrasi Ethernet port 10/100 Mbps

-Support On-line debugger

-Sudah Integrated with Nu-Link-Me so that you no longer need an external programmer

-Package Sale: 1x NuEdu EVB NUC472, 1x NuEdu-Basic 01, Nu-Bridge 1x, 1x USB cable and 1x CD manual

FROG 3D inlay

Frog 3D tags and inlays are designed for pallet and case level applications offering high performance in supply chain management applications.

Frog 3D products have a small, cost-efficient True3D form factor with complete orientation insensitivity providing consistent performance even on challenging materials. High performance Frog 3D inlays deliver excellent read range and are compatible with the Impinj Monza 4 QTTM technology.

Frog 3D tags and inlays are produced using leading edge inlay assembly technologies. Monitoring every step in the production process, from the antenna to the final assembly of the inlay, guarantees optimal quality products.

Overview

• Operating Frequency: 860 - 960 MHz
• Integrated Circuit (IC): Impinj Monza 4
• Antenna Size :50 x 50 mm (1.97 x 1.97 in)
• Die-cut Size :53 x 53 mm (2.09 x 2.09 in)
• Quality Assurance :100% performance tested
• International Standards :EPC Class 1 Gen 2 , ISO 18000-6C

Benefits

• True3D design with complete orientation insensitivity.
• Consistent and robust performance on various materials globally.
• Available in a small and cost-effective form factor.
• Monza 4 QTTM technology capability.
• Possibility for different memory options: EPC from 128 bit to 496 bit and user memory from 32 bit to 512 bit.
• ISO 9001:2008 Quality Management System and ISO 14001:2004 Environment Management System support.