WIZ127SR

WIZ127SR

Feature

- Plug & Play Type Serial to Ethernet Gateway module
- Hardware compatible with WIZ100SR
- 2port serial to Ethernet (supports RS-232 & 422/485)
- Supports TCP & UDP communication
- Supports DHCP, DNS, NTP
- Easy configuration : Web, Telnet, Configuration Tool & Serial Command
- GPIO Extendable (Max. 10GPIOs)
- 10/100 Ethernet & Max.921,600bps Serial Interface

Specification

Specifications		Description
Architecture	MCU	Cortex M3 in W7200
	TCP/IP	W7200
	PHY	W7200
	Memory	W7200 internal Flash : 128Kbytes W7200 internal SRAM : 20Kbytes
Network	Interface	10/100 Base-T Ethernet (Auto Detection)
	Protocol	TCP, UDP, IP, ARP, ICMP, MAC, DHCP, PPPoE
Serial	Interface	2 UARTs (CMOS/TTL compliant), RS-422/485
	Speed	1200bps ~ 921,600bps
	Signals	RS-232 : TXD, RXD, RTS, CTS, GND RS-485 : TRXD+, TRXD- RS-422 : TXD+, TXD-, RXD+, RXD-
Dimension		52mm x 30mm x 8.9mm
Connector Type		2mm Pin Header Type
Input Voltage		DC 3.3V
Power Consumption		TBD
Temperature		0℃~70℃
Humidity		TBD

WizFi250-EVB

WizFi250-EVB Evaluation Board for WizFi250 module 

Features

• - Integrated RF power amplifier : Antenna calibration is not required
• - 1MB Flash Memory, 128KB SRAM and 1MB Serial Flash
• - Supports Low power consumption through dynamic power management mode
• - Provides the highest compatibility with the most of APs
• - Compact Size to fit into any kind of target device, even handheld device such as mobile, PDA and etc
• - Single band 2.4GHz IEEE 802.11b/g/n
• - Providing flexible system configuration through Web
• - RoHS
• - Device Package : 28×20 mm (17×20 mm)
• - Serial Interface : UART, SPI
• - Powerful Web server interface
• - Soft AP(Enough memory retention, L2 Switching)
• - OTA(Firmware Uploading Over the Air)
• - WiFi Direct (going to be prepared by 4Q 2013) 
• -Arduino shield compatible

WizFi250-H

WizFi250-H

Low power "serial to WiFi" module with power amplifier, u.FL connector, PCB antenna and Pin header

The WizFi250-H offers a quick, easy, and cost-effective way for device and appliance manufacturers to add WiFi capabilities to their products. WizFi250 provides UART and SPI interfaces which enable connections to any embedded design utilizing an 8/16/32-bit microcontroller via simple AT commands. WizFi250 is an ideal solution for organizations with limited or no WiFi or RF expertise, as it not only reduces RF design time but also removes the burden of testing and certification, allowing customers; allowing customers to focus on their core application, product, or expertise. WizFi250 is compliant with 802.11b/g/n.

WizFI250-H Features:

• Easy access male Pin header
• Single band 2.4GHz IEEE 802.11b/g/n
• Integrated RF power amplifier
• Supports wireless data rates up to 65Mbit/s
• 1MB Flash Memory, 128KB SRAM, 1MB Serial Flash
• Low power consumption & excellent power management performance extend battery life.
• Small size suitable for low volume system integration.
• Easy for integration into mobile and handheld device with flexible system configuration.
• Lead Free design which supporting Green design requirement, RoHS Compliance.
• Device Package : 28×20 mm (17×20 mm)
• Serial Interface : UART, SPI
• UART Max Baud : 1843200 bps
• Powerful Web server provides
• Soft AP
  • Enough memory retention
  • Wi-Fi Security (WEP, WPA/WPA2PSK)
  • L2 Switching
• OTA(Over The Air F/W Upgrading)

Module specification:

• SKU WizFi250-CA
• Functions S2W (Serial-to-WiFi)
• pre-programmed FW version 1.0
• Standard IEEE 802.11b/g/n
• Band 2,4 GHz
• Antenna U.FL Connector and Printed PCB Antenna (can be removed) 
• Wifi Interface 1T1R RF Interface
• Operation Mode
  • Ad hoc
  • Limited AP
  • Station (Client)
• max. No. of client connections 5
• Security
  • WEP
  • WPA
  • WPA2
• Configuration Interface
  • HTTP Webserver
  • Serial Command
  • Windows Configuration Tool
• Booting Time ~ 1 sec
• MCU I/F SPI, UART
• UART (max speed) 1.8M
• Connector Type SMD
• serial connector count 1
• Serial I/F TTL
• Serial Command Type AT
• SPI (max. speed)  ~ 3 to 5 MHz, tbd.
• I/O ports 8 GPIOs
• MAC address inside
• Auto Negotiation
• Power Down Mode
• Dimension 28 x 20 mm (17 x 20 without PCB Antenna)
• Package SMD module
• pin count 48
• pin pitch 1.00 mm
• Operating Voltage 3.3 V
• voltage regulator (LDO) No
• Power Consumption
  • Normal mode (not associated) 14 mA - 18 mA
  • Normal mode (associated) 67 mA - 69 mA
  • Normal mode (IEEE Power Save mode) 32 mA - 65 mA
  • Stop mode (IEEE Power Save mode) 14 mA - 17 mA
  • Stop mode 3 mA - 23 mA RX = 120mA TX = 265 – 430mA (12dBm - 16dBm; 11b, 11g, 11n)
• TX Output Power 12 – 16.5 dBm ± 1.5dB
• RX Sensitivity -70 to -97 dB (depend on mode)
• Certification
  • CE
  • FCC
  • KCC
• Operating Temperature -20°C to +85°C

The Beaglebone Black Rev C

The BeagleBone Black is the newest member of the BeagleBoard family. It is a lower-cost, high-expansion focused BeagleBoard using a low cost Sitara XAM3359AZCZ100 Cortex A8 ARM processor from Texas Instruments. It is similar to the Beaglebone,but with some features removed and some features added. 

If you liked the BeagleBone Black Rev B, you will love the Rev C! The Rev C still has a blistering 1GHz processor and 512MB onboard DDR3 RAM and like the rev B it has a AM3358 microprocessor, two 46-pin headers, micro HDMI for audio/video output, USB ports, 10/100 Ethernet and other I/O features. The Rev C is an ultra-powered embedded computer that can fit in a mint tin.

The new model includes 4GB of eMMC built-in storage instead of the Rev B's 2GB. With the doubled storage and faster eMMC, the developers were able to make the Rev C's most significant change: shipping the BeagleBone Black with Debian Linux pre-loaded on the board's flash instead of Angstrom Linux. Debian Linux is a more user-friendly operating system than Angstrom and the switch to Debian is partly the result of consumer demand 

The rev C comes with a mini-B cable for powering it up ASAP. No microSD card is included as the BBB has onboard flash storage - and no SD card loading is required to get started. For this revision, CircuitCo has also partnered with Element14 to try and offset some of the demand.

As of May 12, 2014 the BBB comes with Debian Linux w/the 3.8.13-bone kernel

• Processor: Sitara AM3358BZCZ100 1GHz, 2000 MIPS
• Graphics Engine: SGX530 3D, 20M Polygons/S
• SDRAM Memory: 512MB DDR3L 606MHZ
• Onboard Flash: 4GB, 8bit Embedded MMC
• PMIC: TPS65217C PMIC regulator and one additional LDO.
• Debug Support: Optional Onboard 20-pin CTI JTAG, Serial Header
• Power Source: miniUSB USB or DC Jack, 5VDC External Via Expansion Header
• PCB: 86.44mm x 54.54mm / 3.4” x 2.15” 6 layers
• 88.98mm x 54.54mm x 15.41mm / 3.5" x 2.15" x 0.6"
• Indicators 1-Power, 2-Ethernet, 4-User Controllable LEDs
• HiSpeed USB 2.0 Client Port: Access to USB0, Client mode via miniUSB
• HiSpeed USB 2.0 Host Port Access to USB1, Type A Socket, 500mA LS/FS/HS
• Serial Port UART0 access via 6 pin 3.3V TTL Header. Header is populated
• Ethernet 10/100, RJ45
• SD/MMC Connector microSD , 3.3V
• User Input: Reset Button, Boot Button, Power Button
• Video Out: 16b HDMI, 1280x1024 (MAX), 1024x768,1280x720,1440x900 w/EDID Support
• Audio Via HDMI Interface, Stereo
• Expansion Connectors:
  • Power 5V, 3.3V , VDD_ADC(1.8V)
  • 3.3V I/O on all signals
  • McASP0, SPI1, I2C, GPIO(65), LCD, GPMC, MMC1, MMC2, 7 AIN(1.8V MAX), 4 Timers, 3 Serial Ports, CAN0, EHRPWM(0,2),XDMA Interrupt, Power button, Expansion Board ID (Up to 4 can be stacked)
• Weight 40.55g / 1.43oz

ioShield-A

ioShield-A allows an Arduino board to connect to the Internet.

It is based on the WIZ550io network module which uses WIZnet W5500 ethernet chip. The WIZnet W5500 provides a network (TCP/IP) stack capable of both TCP and UDP. It supports up to eight simultaneous socket connections. And, when Powered on and nRESET triggered, WIZ550io initializes itself with embedded real MAC and default IP address and can be pinged from user’s computer.

As ioShield uses W5500 chipset, instead of W5100 which was used before in the Arduino Ethernet Shield,

The ODROID-W

Online Order

The ODROID-W measures a very small 60 x 36 x 7mm (2.4 x 1.4 x 0.3”). new features and improvements over the original Raspberry Pi:

- Li+ rechargeable battery charger and fuel gauge for portables, wearable and robots application

- Real Time Clock to keep accurate time without an Internet connection by just adding a coin battery

- 12-bit precision ADC to measure the dynamic voltage signals via two single-ended inputs 

- DC/DC step-down converters for higher power efficiency

- DC/DC step-up converter for 5Volt rails (USB host and HDMI) from a Li-Polymer battery

- USB Host port can be placed on top or bottom as preferred

- DIY friendly 0.1inch/2.54mm pitch IO connector (up to 32 GPIO ports) for handy prototyping

ODROID-W = RPI + RTC + ADC + UPS + Battery gauge with significant Minimalism

Online Order https://tokopedia.com/rosesana/odroid-w-mini-komputer

HARDWARE SPECIFICATION Processor Broadcom BCM2835 ARM11 700Mhz memory Samsung 4Gbit (512MB) LPDDR2 SDRAM PMIC Ricoh RC5T619 includes DCDCs, LDOs, ADCs, RTC, Battery charger and Fuel gauge DCDC TI TPS61259 is 5Volt step-up DCDC for USB host and HDMI block Video Output HDMI type-D (Micro-HDMI) USB High-speed USB 2.0 host GPIO connectors RPi compatible 13x2-pin header on the top side as well as bottom side for 2-way stacking 20+6 pin header for additional GPIO/ADC/Power/USB connection Total 32 GPIOs and 2 ADCs are available. Camera connector 15pin MIPI-CSI2 (Pi Camera module compatible) Memory card slot Micro-SD (T-Flash) Power Micro-USB socket for 5Volt input Li-Polymer battery connector (Molex 53398-0271) RTC power Backup battery connector (Molex 53398-0271) Dimensions 60 x 36 mm Weight 8 gram

Raspberry Pi or RPi is a trade mark of Raspberry Pi Foundation. Online Order

Elektromagnetic buzzer

BUZZER E-MAG 5V 30mA 83dB PCB

Specification:

• Part Code : HCM1206UX
• Manufacturer: MEC
• ELECTRO MAGNETIC TRANSDUCER, PCB MOUNT 
• Supply: 3-7V @ 30mA
• HOUSED, SELF-DRIVEN

AM7023B Dino-Eye (USB)

AM7023B Dino-Eye (USB)

5 megapixel digital eyepiece that fits in 30mm diameter eyepiece slots 

Dino-Eye Premier AM7023B digital eyepiece is an USB 2.0 powered device that has five megapixels of resolution that allows large detailed images under the microscope with picture sizes up to 2592x1944. The eyepiece fits traditional microscopes with 30mm diameter eyepiece slots and 30.5mm diameter eyepiece slots with its included adapters. Simply remove the optical eyepiece and insert the Dino-Eye to digitalize your microscopy experience.

The Dino-Eye can be found useful for using in either a production line or a laboratory for inspection and documentation. In addition to the merit of digitization, the user can find the experience of using a microscope to be more pleasant and comfortable especially for daily microscope users.

SPECIFICATIONS

Model	AM7023B Dino-Eye (USB)
Interface	USB 2.0
Product Resolution	5M pixels (MJPEG codec may be required to run at 2592 x 1944 resolutions)
Sensor	Color CMOS
Frame Rate	Up to 30fps
Save Formats	Image: DinoCapture2.0: BMP ,GIF ,PNG ,MNG ,TIF ,TGA ,PCX ,WBMP ,JP2 ,JPC ,JPG ,PGX ,RAS ,PNM Movie: DinoCapture2.0: WMV, FLV ,SWF
Measurement Function	Yes
Calibration Function	Yes
Operating System Supported	Windows 7 ,Vista ,XP
Unit Weight	95(g) +/- 10(g)
Unit Dimension	5cm (H) x 3.4cm (D)  Fits 30mm/30.5mm diameter eyepiece slots
Package Dimensions	16cm (L) x 16cm (W) x 6cm (H)

AM7023 Dino-Eye (USB)

AM7023 Dino-Eye (USB)

5 megapixel digital eyepiece that fits in 23mm diameter eyepiece slots 

Dino-Eye Premier AM7023 digital eyepiece is an USB 2.0 powered device that has five megapixels of resolution that allows large detailed images under the microscope with picture sizes up to 2592x1944. The eyepiece fits traditional microscopes with 23mm diameter eyepiece slots. Simply remove the optical eyepiece and insert the Dino-Eye to digitalize your microscopy experience.

The Dino-Eye can be found useful for using in either a production line or a laboratory for inspection and documentation. In addition to the merit of digitization, the user can find the experience of using a microscope to be more pleasant and comfortable especially for daily microscope users.

SPECIFICATIONS

Model	AM7023 Dino-Eye (USB)
Interface	USB 2.0
Product Resolution	5M pixels (MJPEG codec may be required to run at 2592 x 1944 resolutions)
Sensor	Color CMOS
Frame Rate	Up to 30fps
Save Formats	Image: DinoCapture2.0: BMP ,GIF ,PNG ,MNG ,TIF ,TGA ,PCX ,WBMP ,JP2 ,JPC ,JPG ,PGX ,RAS ,PNM DinoXcope: PNG ,JPEG Movie: DinoCapture2.0: WMV, FLV ,SWF DinXscope: MOV
Measurement Function	Yes
Calibration Function	Yes
Operating System Supported	Windows 7 ,Vista ,XP
Unit Weight	95(g) +/- 10(g)
Unit Dimension	5cm (H) x 3.2cm (D)  Fits 23 diameter eyepiece slots
Package Dimensions	16cm (L) x 16cm (W) x 6cm (H)

AM4023X Dino-Eye (USB)

AM4023X Dino-Eye (USB)
Digital eyepiece that fits eyepiece slots with 23mm, 30mm, or 30.5mm apertures. 

The Dino-Eye Premier AM4023X digital eyepiece is a very adaptable digital eyepiece that can fit 23mm, 30mm, and 30.5mm eyepiece slots with its included adapters with its tubular design that is great for setting the right focal point for different types of microscopes. It has a 1.3 megapixel sensor with the ability for long exposures that's great for low light visibility. It allows clear and visible examination of specimens and superb viewing on a computer monitor.

The Dino-Eye can be found useful in a laboratory for observation and documentation, a production line for inspection, and much more. In addition to the merit of digitization, the user can find the experience of using a microscope to be more pleasant and comfortable especially for daily microscope users.

SPECIFICATIONS

Model	AM4023X Dino-Eye (USB)
Interface	USB 2.0
Product Resolution	1.3M pixels. (SXGA)
Sensor	Color CMOS
Frame Rate	Up to 30fps
Save Formats	Image: DinoCapture2.0: BMP ,GIF ,PNG ,MNG ,TIF ,TGA ,PCX ,WBMP ,JP2 ,JPC ,JPG ,PGX ,RAS ,PNM DinoXcope: PNG ,JPEG Movie: DinoCapture2.0: WMV, FLV ,SWF DinXscope: MOV
Measurement Function	Yes
Calibration Function	Yes
Operating System Supported	Windows 7 ,Vista ,XP MAC OS 10.4 or later
Unit Weight	100(g) +/- 10(g)
Unit Dimension	7.2cm (H) x 2.3cm (D)
Package Dimensions	16cm (L) x 16cm (W) x 6cm (H)