Thursday, January 18, 2018

Goot 60 watt solder element

Goot solder element with 220 VAC working voltage and 60 watt power.

LT1167AIS8PBF oamp chip

LT1167AIS8PBF is an Op-Amp IC with 1 MHz bandwidth gain and maximum working voltage of 20 V. Suitable for application on bridge amplifier, thermocouple amplifier, strain gauge amplifier, etc.

  • Power supply 20 V (max)
  • SOIC-8 packaging
  • Input offset voltage 40 μV (max)
  • Input bias current 350 pA
  • Gain bandwidth 1 MHZ


datasheet https://goo.gl/2J1PkE

T40P-194BO-HS4 Black/Orange BaneBots Wheel

BaneBots Wheel, 1-7 / 8 "x 0.4", 1/2 "Hex Mount, 40A, Black / Orange T40P-194BO-HS4
Rubber wheels for applications in the field of robotics with a diameter of 1-7 / 8 ", width 0.4", and type hub hex mount 1/2 ".

Specification:
- Outside Diameter: 1-7 / 8 in
- Width: 0.4 in
- Mount: 1/2 in hex
- Color: Black and orange

T40P-195BA-HS4 Black/Blue BaneBots Wheel

BaneBots Wheel, 1-7 / 8 "x 0.4", 1/2 "Hex Mount, 50A, Black / Blue T40P-195BA-HS4
Rubber wheels for applications in the field of robotics with a diameter of 1-7 / 8 ", width 0.4", and type hub hex mount 1/2 ".

Specification:
- Outside Diameter: 1-7 / 8 in
- Width: 0.4 in
- Mount: 1/2 in hex
- Color: Black and blue

IRF3415 mosfet

IRF3415 is an N-channel MOSFET with 150V drain-source breakdown voltage and 43 A drain current.


  • TO-220-3 packaging
  • N-Channel Polarity
  • Power dissipation 200 W
  • Drain source breakdown voltage 150 V
  • Gate-source voltage 20 V
  • Continuous drain current 43 A

U2D2 USB Communication Converter

U2D2 is a USB converter device that serves as a bridge to connect and control Dynamixel servo to PC / laptop. U2D2 can be connected to laptop / PC by using micro USB cable. U2D2 supports both TTL and RS-485 interfaces as a communication path to various Dynamixel servo-servo variants. In addition U2D2 also supports UART interface as a communication path to OpenCM9.04, CM-150 and CM-200.
U2D2 can be used to configure & test servo conditions, firmware upgrade and recovery, servo ID replacement, and various other functions.
datasheet https://goo.gl/uezrck

AT59C11 chip

4-Wire Serial EEPROM

  • 5 VDC power supply
  • 8-pin DIP packaging
  • 4-wire interface
  • Capacity 128 bytes
  • Time of reading / writing of data 10 ms


datasheet https://goo.gl/uCRU1H

DS1921G-F5 1-wire thermo sensor

Sensor for digital thermometer with an accuracy of ± 1 ° C from -30 ° C - + 70 ° C which has 1 wire interface.
https://datasheets.maximintegrated.com/en/ds/DS1921G.pdf

Tuesday, January 16, 2018

Saturday, January 13, 2018

P8751BH micro chip

8-bit microcontroller MCS-51 family oriented control.
  • 40-pin DIP packaging
  • 12MHz working frequency (max)
  • Working voltage of 5VDC
  • Number of i / o 32
  • 8051 Architecture
  • Memory size of 4k Byte program
  • 128 byte volatile data memory size
  • Timer / counter Timer / Counter 16-bit
  • UART peripheral interface


datasheet: https://docs.google.com/open?id=0BzkNNhuEnaF-aHlxdDJfczBPM00

TD62004AP chip 16-DIP

TD62004AP chip 16-DIP 7-channel Darlington Sink Driver
datasheet http://www.toshiba.com/taec/components2/Datasheet_Sync//393/7032.pdf

DS3231MZ+TRL

IC RTC with I²C interface in NSOIC-8 pin packaging. It has been integrated with MEMS (MicroElectroMechanical Systems).

Features:
- Full function for calendar, hour (second, minute, hour, day, date, month and year).
- Accuracy timekeeping ± 5 ppm (± 0.432 sec / day) with working temperature -45 ° C to 85 ° C.
- Output 1 Hz and 32,768 kHz.
- Power supply: 2.3V - 5.5V.

http://www.farnell.com/datasheets/2001796.pdf?_ga=1.59084260.898254825.1447042516

Friday, January 12, 2018

74HC74A SOIC-14 chip


Dual D-type Flip-Flops (with Preset and Clear)


  • 2 -6 VDC power supply
  • 14-lead SOIC packaging
  • Function D Flip-flop with preset and clear
  • Propagation delay 150 ns
  • Level of voltage i / o TTl

SD Card memory 8 GB V-GEN

SD card V-GEN brand with a memory capacity of 8 GB. This memory is included in the class 6 SD card, which is capable of reading data at a maximum speed of 25 MB / s and capable of writing data with a maximum speed of 12.3 MB / s.
It is suitable when used as a storage medium for digital cameras.

Specification:
- Type: SD card
- Capacity: 8 GB
- Class: Class 6
- Read Speed: 25 MB / s
- Write Speed: 12.3 MB / s
- Dimensions: 32 x 24 mm

Dekko multimeter probe

Dekko multimeter probe with cable length 120 cm.

Stanley Digital Voltage Tester

Stanley Digital Voltage Tester

is a portable voltage measuring device with 2 methods of measurement, contact and contactless. This means that this device can be used to measure voltage by touching the probe to a voltage source directly (contact) or can also be used to measure the voltage without touching the source of voltage directly (contactless).

To display the reading result, the LCD graph has been provided 0.75 ".The device is compatible for 12 - 220V voltage range either AC or DC.

DS2422S chip

DS2422S chips are temperature sensors in which there are real time clock (RTC), memory, serial interface for ADC, dataloggers, and 1-Wire interface.

datasheet https://datasheets.maximintegrated.com/en/ds/DS2422.pdf

Thursday, January 11, 2018

AD7663AST

16 bit CMOS ADC
Specification:
- Sampling rate of 250 kSPS
- 16 bit resolution
- Parallel Interface (8/16 Bits) and Serial 5V / 3V
- Supply 5V
- Package LQFP-48

LM2904N chip

Dual Operational Amplifier.
  • Power supply 3V - 26V (or ± 1.5V - 13V)
  • Output current 30 mA (Typ I source) and 15 mA (Typus I sink)
  • Package DIP-8
  • Input offset voltage (max) 0.7mV
  • Input bias current max) 250nA
  • Gain bandwidth 100dB


datasheet http://www.ti.com/lit/ds/symlink/lm358.pdf

AT24C512B-PU-1.8 chip

Serial EEPROM
  • 1.8VDC power supply - 3.6VDC
  • 8-pin DIP packaging
  • I2C interface
  • Capacity 64 Kbytes
  • Time of reading / writing data 5 ms (write cycles)


datasheet http://atmel.com/dyn/resources/prod_documents/doc5297.pdf

182K OHM 0.25W 1% (10 pcs per pack)

Resistor with 182K ohm resistance

  • Tolerance of 1%
  • Obstacles 182K ohm
  • Power 0.25 W

MAX153CPP chip

High speed 8 bit ADC with 1uA Power-Down
Specification:
- Single power supply + 5V or Dual ± 5V
- Supply current 8mA
- External voltage reference
- Conversion Time 0.66 us Max.
- 8 bit resolution
- 1MHz max bandwidth
- 1 analog input channel
- Operating range 0 - 70 degree celcius
- Package 20-pin Narrow PDIP

datasheet http://www.mouser.com/ds/2/256/MAX153-101958.pdf

MAX127BCAI SSOP28

12-bit DAS (Data Acquisition Systems) 2-wire interface.
Specification:
- Resolution: 12-bit.
- 8 analog input channels.
- 8ksps sampling rate.
- Internal 4.096V / external reference.
- Linearity 1/2 LSB.
- Single supply: +5 VDC.
- Interface: I2C / 2 wire serial interface.
- Software-selectable input range: 0 to + 10V, 0 to + 5V, +/- 10V, or +/- 5V.
- 2 power down modes.

datasheet at https://datasheets.maximintegrated.com/en/ds/MAX127-MAX128B.pdf

CNY17-2 chip 6-DIP

Optocoupler with phototransistor output
  • Emitter voltage 1.25 V
  • Backlight emitter 5 V
  • Output component (transistor / triac) NPN transistor
  • 10 V output voltage (tested)
  • Output current 100 mA (absolute max)
  • Insulation Voltage 5000 VRMS
  • Switching speed 3 us
  • 6-pin DIP packaging


datasheet at http://www.vishay.com/docs/81863/81863.pdf

MCP2150-I/P

IC IrDA Standart Protocol stack Controller that supports DTE Application.
Specification:
- Supply voltage 5V
- Implements the IrDA standard including: IrLAP, IrLMP, IAS, TinyTP, IrCOMM (9-wire cooked service class)
- UART to IrDA standard encoder / decoder
- Easily interfaces with industry standard UARTs & infrared transceivers
- Hardware Baud rate selection
- Infrared baud rate supported: 9.6Kbaud, 19.2Kbaud, 38.4Kbaud, 57.6Kbaud, 115.2Kbaud
- 64 Byte data packet Size
datashet at http://ww1.microchip.com/downloads/en/DeviceDoc/21655C.pdf

Header 40x1 with 18mm height

40x1 header that has 18mm height


  • Types of PCB Header terminals
  • Male (male / female) form
  • Pitch 2.54 mm
  • Number of pins 40 x 1
  • Mounting PCB

DB25 Extension Cable M/F 120cm

Extension cable for Parallel port (DB25 Male-Female)
Specifications:
- Connector: Male-Female
- Cable length: 120 cm

D-Sub Contact Crimping Tool

D-Sub Contact Crimping Tool
Crimping device for female & male D-SUB minuature contact.

Specification:
- OAL: 240 mm
- Applications: AWG24-30, 18-22
- Material:
- HRC: 45 ± 3
- Material: AISI1050, AISI4140
- Handle: PP

Tuesday, January 09, 2018

Tantalum 2.2uF / 25V

Capacitor tantalum with capacitance value of 2.2uF

  • Capacitance 2.2 uF
  • Voltage 25 V

Transistor BC160

PNP Silicon transistor

  • TO-39 packaging
  • Type of PNP
  • Max continuous collector current (ic) 1 A
  • Maximum voltage collector-emitter (vce) 40 V
  • Minimum base-collector voltage on-state (vbe) sat -
  • Maximum collector-emitter saturation voltage (vce) sat 0.6 V
  • Hfe 1.25
  • Bandwidth 50 MHz

Transistor 2SD1163

Silicon NPN tripple diffused transistor

  • TO-220AB packaging
  • Type of NPN
  • Max continuous collector current (ic) 7 A
  • The minimum voltage of the on-state (vbe) base-collector sat 1.2 V (MAX)
  • Maximum collector-emitter (vce) saturation voltage is 2.0 V
  • Hfe 25

Adapter RJ45 jack 8P8C female to female

Adapter RJ45 jack 8P8C female to female
Connector for Rj-45 connection with female to female configuration. It has two RJ-45 connectors on the front and back.

Monday, January 08, 2018

SC34-A1 IDC Socket

SC34-A1 IDC Socket
IDC socket 34pin

1N5341B Zener 6.2V, 5W

Zener 5W, 6.2V

  • Packaging T-18
  • Voltage 6.2V
  • Power 5W
  • 1 Ohm input impedance (@ 200mA)
  • 1uA reverse leakage

Zener 27V

General purpose zener diode with a voltage of 27 V.

  • Voltage 27 V

Jack Audio Stereo 3.5mm Male to 2.5mm Female Adapter

male stereo audio jack with jack diameter of 3.5 mm. This jack uses metal housing with silver bandage on the surface.


  • Jack Audio terminal type
  • Male (male / female) form
  • Number of pins 3
  • Mounting cables
  • Mounting angel Straight
  • Metal packaging materials

Switch DPDT - 110VAC/220VAC

6-pin slide / slide switch with DPDT configuration.


  • Number of pins 6
  • DPDT Configuration
  • Slide type switch
  • Logic ON / OFF

Sunday, January 07, 2018

MTW1206X (6V DC) Electro-Magnetic Buzzer

Electro Magnetic Buzzer
Technical specifications:
- Operating Voltage = 6VDC
- Sound Output = 85 dB

Saturday, January 06, 2018

BNC Male Connector (PVC)

BNC Male (plug) Connector with Impedance: 75 ohm and DC frequency range - 1GHz.

  • Type of BNC Connector terminal
  • Male (male / female) form
  • Metal contact material
  • Pvc packing materials

KSG-50A 4mm Socket, Gold (blue)

Socket KSG-50A, blue color, diameter 4 mm

  • Kind of terminal Socket KSG-50A
  • Gold-Plated contact material
  • Flow 19A / 50V

Epistar P10 Outdoor RED Led Module

Epistar P10 Outdoor Led Module in red
dot matrix display panel designed for outdoor purposes, making it more resistant to weather. Composed of oval LED difused for optimum viewing angle of outdoor application. This module can be assembled easily using pin connectors whose cables are provided in the purchase package.
The dot matrix display panel can be controlled using a ready-made controller or it can be programmed manually using a microcontroller.

Specification:
- Working Voltage: 5 VDC
- Red
- Resolution: 16 x 32 dots
- Best Visibility: 12 - 50 m
- Dimensions: 160 x 320 mm
- Refresh Frequency: 120 Hz

Friday, January 05, 2018

Development board for Motorola 68HC908QT4

Development board for Motorola 68HC908QT4 microcontroller with serial communication UART RS232.
Specification:
- Using a family microcontroller HC08-Q from freescale
- Include Software Development Code Warrior
- Programs can be modified using ASM or C language
- Sales package includes: Development tool, serial cable, CD Code warrior, 9V Battery

http://cache.freescale.com/files/soft_dev_tools/doc/support_info/M68DEMO908QT4SCH.pdf?fpsp=1

Thursday, January 04, 2018

2.4GHz Antenna 2.15dBi Height 100mm Black

Antenna for 2.4GHz black color


  • Dimensions Height 100 mm
  • 2.4 GHz working frequency
  • Voltage standing wave ratio (vswr) 1.5
  • The input impedance is 50 Ohm
  • Gain 2.15 dBi

Banana Jack 4mm black small

Banana Jack small with size 4mm black color

Banana Plug green 4mm

Banana Plug in green

  • Type of terminal Banana Plug

Banana Plug red 4mm

Banana plug is red with a diameter of 4 mm

  • Type of terminal Banana Plug

Epistar Outdoor Green P10 Led Module

dot matrix display panel designed for outdoor purposes, making it more resistant to weather. Composed of oval LED difused for optimum viewing angle of outdoor application. This module can be assembled easily using pin connectors whose cables are provided in the purchase package.
Pane dot matrix display can be controlled using ready to use controller or can also be programmed manually using microcontroller.

Specification:
- Working Voltage: 5 VDC
- Green color
- Resolution: 16 x 32 dots
- Best Visibility: 12 - 50 m
- Dimensions: 160 x 320 mm
- Refresh Frequency: 120 Hz

Tuesday, January 02, 2018

Pro's Kit 1580 Tie Points Round Hole Bread Board

breadboard / project board measuring 175 x 188 mm with a total of 1580 holes for placing electronics components.

Specification:
- Dimensions: 175 x 188 mm
- Number of Holes: 1580
- Using round hole type / rounded so that the user easier in installing and removing components
- Housing made of sturdy ABS material and contact made of conductive bronze phospor.

Relay DPDT HKE HRS2H-S 12VDC

DPDT Relay brand HJR with specifications: - Coil working voltage: 12 VDC. - Contact rating: 0,5A - 120VAC / 1A - 24VDC.