Showing posts sorted by date for query usb2dynamixel. Sort by relevance Show all posts
Showing posts sorted by date for query usb2dynamixel. Sort by relevance Show all posts

Saturday, April 14, 2018

BIOLOID 3P Cable 100mm

3 pin cable for AX-Series servo motor, MX-Series servo, CM-Series controller and USB2Dynamixel.
Specifications:
- Cable length: 100mm
- Number of pins on each connector: 3pin
- Number of cables: 10 pcs
- Compatible for dynamixel servo motor: AX-12 +, AX-12A, AX-18F, AX-18A, MX-28T, MX-64T, MX-106T
- Compatible for controllers: CM-2 +, CM-5, CM-510, CM-530, CM-700, CM-900
- Compatible for USB2Dynamixel, SMPS2Dynamixel

Saturday, February 28, 2015

Robotis MX-64 Gear/Bearing Set

With the MX-64 Gear Set you can replace worn or damaged gears in your DYNAMIXEL MX-64.

Each gear is metal and has a special coating to increaste endurance and durability. The Wheel gear also has a built in magnet, which is crucial to the magnetic encoder in the servo.

This kit included 5 gears, grease, 1 bearing, and a calibration adapter tool.

These gears are compatible with both the MX-64T and MX-64R. They are not compatible with the RX64 servos. You will need a USB2DYNAMIXELto calibrate the servo after you have replaced the gears.

Robotis MX-28 Gear /Bearing Set

With the MX-28 Gear / Bearing Set you can replace worn or damaged gears in your DYNAMIXEL MX-28.

Each gear is metal and has a special coating to increase endurance and durability. The Wheel gear also has a built in magnet, which is crucial to the magnetic encoder in the servo.

This kit included 5 gears, grease, 2 bearings, and a calibration adapator tool.

These gears are compatible with both the MX-28T and MX-28R. They are not compatible with the RX28/RX24 servos. You will need a USB2DYNAMIXEL to calibrate the servo after you have replaced the gears.

Friday, October 17, 2014

Dynamixel MX-12W Robot Actuator

Dynamixel MX-12W Robot Actuator

The MX-12W from ROBOTIS is the Goldilocks of servos; everything about it is just right. It has the compact size of the AX-12A and AX-18A (and uses the same housing) yet has the electronics and control capabilities of the high performance MX servos like the MX-28T and MX-64T.
This is the only servo at this size and cost, that is capable of true position control for multiple rotations. If you've ever tried to get more than one revolution out of your servo and been frustrated with losing your position for multiple turns the MX-12W is the solution for your next project. Switch the servo from joint mode (the default) into multi-turn mode to take advantage of this new and exciting feature. At the default resolution it is capable of 14 rotations, but by increasing the resolution divider from 1 to the maximum of 4, you can get up to 56 rotations (at 0.35°/step) without losing a single step.

Features

  • 14 to 56 revolutions with real position control and feedback
  • Position, temperature, load, and input voltage feedback
  • PID control for high accuracy
  • Contactless absolute encoder
  • 12 V operating voltage
  • TTL communication for easy daisy chaining
  • 470 RPM no load speed
  • 32 x 40 x 50 mm compact size
  • 54.6 g weight
The MX-12W is perfect for applications where you want a lot of precision (up to 4096 steps/rev) and speed (470 RPM) without consuming a lot of power (0.6 A stall current). You can use the AX-12A compatible brackets and Bioloid frames to mount the servo and control using any of the DYNAMIXEL controllers such as the OpenCM9.04-B. The MX-12W is also compatible with the CM-5, CM-510, CM-530, and CM-700. You can also use the USB2Dynamixel adapter with the free RoboPlus software.
Like other DYNAMIXEL Robot Actuators, the MX-12W servos are network driven using the TTL communication protocol, which means they can each be addressed with a unique ID. By default, each servo usually comes set to ID #1 and at 1 Mbps baud rate. Be sure to change those to suit your needs if you connect more than one servo together to avoid conflicts. The ID can be set dynamically, making it easy for users to configure their actuators for their specific robot.
Like most other DYNAMIXEL robot servos, the MX-12W uses a standard 3 pin connector. Because of this, the MX-12W can be linked with any other DYNAMIXEL servo at the voltage and baud rate. This makes it easy to mix large and small size, high and low torque, and fast and slow speed servos in one robot without any added wiring complexity.

Package Contents

  • 1 x DYNAMIXEL MX-12W
  • 1 x horn spacer
  • 1 x plastic frame
  • 1 x 3 pin, 200 mm long cable
  • 1 x M3-10 pan head bolt
  • 16 x M2-6 pan head bolt
  • 16 x M2 nuts
Plenty of support material is available for the MX-12W including complete documentation, specifications, software downloads, and 3D CAD models. However, because this servo is so new, some of the performance and programming information from ROBOTIS is still be updated and may not be completely accurate.

Friday, May 02, 2014

Dynamixel AX-12A 6pcs Bulk.

Dynamixel AX-12A 6pcs Bulk

The AX-12A is a Serially Controlled servo that provides some 50 commands and feedback parameters to allow complete control over your robot application. 

The Serial protocol is daisy chained, meaning several servos can be connected to each other in a chain and offer several compliance and sensing parameters that can be configured and read including position, velocity and temperature.


The AX-12A is a new version of the popular AX-12+ with the same performance but more advanced external design and improved gear durability. It is 100% compatible with AX-12+ at 1:1 scale, and retains the same control method and protocol.



Hardware Specifications
  • Weight : 54.6g
  • Dimension : 32mm x 50.1mm x 40mm
  • Minimum Control Angle : 0.29° X 1,024
  • Gear Ratio : 254 :1
  • Holding Torque : 15kgf.cm (at 12V, 1.5A)
  • No Load Speed : 59 RPM 12V
  • Motor : Cored Motor
  • Operating Mode :
    1. Actuator Mode (0° ~ 300°)
    2. Wheel Mode (Endless Turn)
  • Operating Temperature : -5C ~ +70C
  • Operating Voltage : 9V~12V (Recommended Voltage 11.1V)
  • Maximum Currents : 900mA
  • Standby Currents : 50mA
  • Command Signal : Digital Packet
  • Protocol Type : Half duplex Asynchronous Serial Communication (8bit, 1stop, No Parity)
  • Link (Physical) : TTL Level Multi Drop (Daisy Chain Type Connector)
  • ID : 254 ID (0~253)
  • Communication Speed : 7843bps ~ 1 Mbps
  • Feedback : Position, Temperature, Load, Input Voltage, etc
  • Material : Engineering Plastic
  • Position Sensor : Potential meter
Default Settings:
  • ID: 1
  • Baud rate: 1 Mbps
  • Serial Interface Half Duplex TTL interface
  • * Please change the setting of ID and baud rate depending on your operating environment.
Compatible Products:
  • Controller : CM-5, CM-510, CM-700
  • Interface(I/F) : USB2Dynamixel
  • Frame : Frames for Bioloids
Controlling Environment
  • Software for Dynamixel control : ROBOPLUS 
  • C/C++, C#, Labview, MATLAB, Visual Basic etc. : Library 
Package Contents:
  • AX-12A: 6 units
  • THIS PACKAGE DOES NOT INCLUDE ANY ACCESSORY, ONLY THE SERVOS

Thursday, May 01, 2014

Dynamixel MX-64T Robot Actuator.

Dynamixel MX-64T Robot Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new TTL 2.0 bus. 
Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can be adjusted individually for each servo, allowing you to control the speed and strength of the motor's response. 

All MX Series servos use 12v nominal voltage, so MX Dynamixels can be mixed without having to worry about separate power supplies. All of the sensor management and position control is handled by the servo's built-in microcontroller. This distributed approach leaves your main controller free to perform other functions.


MX-64T Stats
Operating Voltage14.8V12V
Stall Torque74 kg·cm
1033 oz·in
7.3 N.m
61 kg·cm
849 oz·in
6.0 N.m
No-load Speed78 RPM63 RPM
Weight126g
Size40.2 x 61.1 x 41.0 mm
Resolution0.088°
Reduction Ratio1/200
Operating Angle360° or Continuous Turn
Max Current4.1A @ 12V
Standby Current100 mA
Operating Temp-5°C ~ 80°C
ProtocolTTL
Module Limit254 valid addresses
Com Speed8000bps ~ 3Mbps
Position FeedbackYes
Temp FeedbackYes
Load Voltage FeedbackYes
Input Voltage FeedbackYes
Compliance/PIDYes
MaterialMetal Gears &
Engineering Plastic Body
MotorMaxon RE-MAX


Controller ListUSB2Dynamixel
CM-700

Thursday, February 06, 2014

SMPS2Dynamixel


provides power from the SMPS to the dynamixel. Connect the SMPS(for CM-5) to the DC terminal and connect the dynamixel using the cable. There are two 3P connector for AX series and two 4P connector for DX/RX series mounted on the SMPS2Dynamixel.


The power line and communication line are all connected making it capable of becoming the role of the dynamixel expansion bus. When controlling the dynamixel with the USB2Dynamixel, power can be easily supplied. Can be used by connecting to a proper DC terminal. Can be used according to each dynamixel's proper voltage. However, the maximum supply voltage is 20V.


A shrink tube is used to cover the circuit part to protect it from short circuit from metal substances.

Wednesday, January 29, 2014

10 pcs BIOLOID 3P Cable @200mm

3 pin cable for servo motor AX-Series, CM-Series controller and USB2Dynamixel.

specifications: 
- Cable length: 200mm
- The number of pins on each connector: 3pin
- Number of wires: 10 pcs /1 set.
- Compatible for Dynamixel servo motor: AX-12 +, AX-18F, AX-S1
- Compatible for controller: CM-2, CM-5, CM-510
- Compatible for USB2Dynamixel, SMPS2Dynamixel

Friday, January 10, 2014

Dynamixel MX-64T Bulk pack (6pcs)



The MX-64T Dynamixel Robot Servo Actuator is the newest generation of Robotis Dynamixel actuator; equipped with an onboard 32bit 72mhz Cortex M3, a contact-less magnetic encoder with 4x the resolution over the AX/RX series, and up to 3mpbs using the new TTL 2.0 bus. Each servo has the ability to track its speed, temperature, shaft position, voltage, and load. As if this weren't enough, the newly implemented PID control algorithm used to maintain shaft position can be adjusted individually for each servo, allowing you to control the speed and strength of the motor's response. All MX Series servos use 12v nominal voltage, so MX Dynamixels can be mixed without having to worry about separate power supplies. All of the sensor management and position control is handled by the servo's built-in microcontroller. This distributed approach leaves your main controller free to perform other functions.




MX-64T Stats
Operating Voltage14.8V12V
Stall Torque74 kg·cm
1033 oz·in
7.3 N.m
61 kg·cm
849 oz·in
6.0 N.m
No-load Speed78 RPM63 RPM
Weight126g
Size40.2 x 61.1 x 41.0 mm
Resolution0.088°
Reduction Ratio1/200
Operating Angle360° or Continuous Turn
Max Current4.1A @ 12V
Standby Current100 mA
Operating Temp-5°C ~ 80°C
ProtocolTTL
Module Limit254 valid addresses
Com Speed8000bps ~ 3Mbps
Position FeedbackYes
Temp FeedbackYes
Load Voltage FeedbackYes
Input Voltage FeedbackYes
Compliance/PIDYes
MaterialMetal Gears &
Engineering Plastic Body
MotorMaxon RE-MAX
Manual DownloadMX-64 Manual
Controller ListUSB2Dynamixel
CM-700

Friday, October 26, 2012

Bioloid GP Kit


Bioloid GP Kit is a humanoid robot kits that have been optimized for different types of robot competitions. Bioloid GP Kit is equipped with actuators which have high torque, communication devices, sensors, and frame of aluminum a sweat yet powerful. Bioloid GP Kit can be formed into a humanoid robot with 16 degrees of freedom (16 DOF). Bioloid GP Kit also comes with a gripper to pick up an object, Kung-Fu movement, attack, and dribble-purpose robot soccer competition.


Specifications: 
  • Using the CM-510 controller ATmega2561 based. 
  • Using actuators: 
  •  -- 8 AX-12A with torque capacity up to 15 kgf.cm. 
  •  --10 AX-18A with torque capacity up to 18 kgf.cm. 
  • Equipped with gyro sensor (2 axis) and distance sensors DMS (Distance Measurement Sensor). 
  • Equipped with remote controller RC-100Z consisting of remote controller RC-100 and ZIG-110 to control the robot wirelessly. 
  • USB2Dynamixel that can be used to connect the CM-510 to a computer's USB port. 
  • A set of polished aluminum frames are lightweight yet strong enough to build a robot body. 
  • Equipped with 1 set of gripper for certain applications such as taking an object. 
  • Humanoid robots can do Kung-Fu move, attack, or dribble. 
  • Rechargeable batteries (11.1V Li-Po, 1000 mA / PCM) as the robot power supply. 
  • SMPS (12V, 5A) for external power supply and battery charging. 
  • Equipped with some tools like wrenches, screwdrivers, and a cable holder. 
  • Balance battery charger to help the process of charging the battery. 
  • Equipped with a suitcase made from aluminum, making it easier to keep robots and equipment. 
  • Equipped RoboPlus software for robot programming. 
  • The process is a serial programmer using the included serial cable. 
  • Equipped with the Assembly Manual (Quick Start) to assemble Humanoid robot with 16 degrees of freedom (16 DOF). 
  • Bioloid GP Kit height: 346 mm (13.6 inch). 
  • Robot Weight: 1.6 kg (56.43 oz). 

Bioloid GP Supplies Kit: 
  1. 1 Bioloid CM-510 MCU (Atmel ATMega128) controller. 
  2. 8 Dynamixel AX-12A serially controlled servos. 
  3. 10 Dynamixel AX-18A serially controlled servos. 
  4. 1 gyro sensor (2 axis) GS-12. 
  5. 1 sensor distance DMS (Distance Measuremnent Sensor). 
  6. 1 remote controller RC-100z (RC-100 + 1 set ZIG-110). 
  7. 1 LED holder. 
  8. 1 Rechargeable Li-Po battery (11.1V/1000 mA). 
  9. 1 CD software RoboPlus. 
  10. 1 Switch Mode Power Supply (12V/5A) and balanced battery charger. 
  11. 1 Serial cable BSC-10 (9pin D-type). 
  12. 1 set of wires. 
  13. 1 set of tools such as bolts, nuts, screws, rivet, and wrenches. 
  14. 1 pcs rivet box. 
  15. 1 Bioloid GP Aluminum Frame Set. 
  16. Quick Start Manual. 
  17. 1 suitcase made from aluminum.
other article: http://2r-he.blogspot.com/2011/04/bioloid-gp.html

Monday, November 14, 2011

BIOLOID 3P Cable Set BCS-3P01

3 pin connector cable for the AX series Dynamixel.

Specifications Bioloid Cable Set BCS 3P-3P01:
Both ends of the cable is equipped with a 3 pin socket which is compatible with AX series Dynamixel.
There are several options such as cable length: 60 mm, 100 mm, 140 mm, 180 mm and 200 mm.

Compatible with products such as:
  • Dynamixel AX12/AX-12 + / AX-12A/AX-18F/AX-18A/AX-S1.
  • Controller Module CM-5, CM-510, CM-700 and CM-2 +.
  • USB2Dynamixel and SMPS2Dynamixel.


Supplies Bioloid Cable Set BCS 3P-3P01:
  • 60mm 3P Cable: 6 pcs.
  • 3P Cable 100mm: 5 pcs.
  • 3P 140mm Cable: 6 pcs.
  • 3P Cable 180mm: 4 pcs.
  • 3P Cable 200mm: 5 pcs.

Tuesday, March 08, 2011

USB2Dynamixel

USB2Dynamixel is a device used to operate Dynamixel directly from PC.  USB2Dynamixel is connected to USB   ort of PC, and 3P and 4P connectors are installed so that various Dynamixels can be conntected. 

Also, USB2Dynamixel can be used to change from USB   ort to Serial   ort on the PC without serial   port such as notebook computer, etc.  The function is very useful in the cases when the Dynamixel exclusive controllers such as CM-2, CM-2+, CM-5, and CM-510 are connected to USB Port, or when ZIG2Serial is connected to USB   or to control robots wirelessly.

The communication mode can be selected by chaning the switch of USB2Dynamixel as below.

1. TTL Communication : Dynamixels using 3- in ort such as AX Series, AX-S1 etc.
2. RS485 Communication : Dynamixels using 4- in ort such as DX Series, RX Series, EX Series etc.
3. RS232 Communication : Controllers using serial cable such as CM-5, CM-510 etc.

Monday, November 22, 2010

Bioloid Premium Kit

Bioloid Premium Kit
It is the upgraded and latest version of Bioloid Comprehensive Kit. (Expert Kit - Labs version of Comprehensive Kit)
Bioloid includes gyro sensor, DMS sensor, and multi-channel wireless expendable remote controller. (Based on Premium Kit) Please make sure that it is easy to insert and take out the batteries; the cables are arranged safely; it has outstanding compatibility.

Components
-CM-510 (Main Controller): 1 piece

RoboPlus is an icon-type, C language-based, and easy-to-use software for users who do not understand computer program languages. The motions and behaviors of robots can be programmed and managed with the software. The users can learn the structure and the grammar of C language eventually while using RoboPlus. In addition, various C language program examples are provided for experts. 


* CPU: ATMEGA 2561
* Internal I/O Device: 6 buttons, Mic, Temperature sensor, and Voltage Sensor are included
* External I/O Device: GP I/O & 6 of 5P I/O port for analog sensor installation AX-Series Dinamixel connector: 5 pieces
* Mode Display & AUX LED

- Robot Exclusive Servo Dynamixel(AX-12+): 18 pieces
- 2-axis Gyro Sensor: 1 piece
- DMS Sensor: 1 piece
- IR sensors: 2 pieces
- RC-100(Remote Controller): 1 piece
- Skin Set for Humanoid
- Li-Po Battery (11.1V, 1000mA/PCM) : 1 piece
- Battery Charger
- USB2Dynamixel
- Quick Start Book (3-types of humanoid robot examples are provided)
- Screw Driver, Cable Holder
- RoboPlus CD

Merits
1) Excellent walking humanoid (Self-Adjusts posture while walking)
2) Various sensors including Gyro, Distance, and IR
3) RC-100(Remote Controller) is included (IR-default, Zigbee-optional)
4) C-style programming & motion teaching with RoboPlus S/W (USB interface included)
5) Semitransparent humanoid skin for customization
6) Digital packet communication with daisy chain topology
7) Build various robots through versatile expansion mechanism 

Comparison table:
Description Bioloid Beginner Kit Bioloid Comprehensive Kit Bioloid Premium Kit
Web Links Web Link another Web Link
Main Controller CM-5 CM-5 CM-510
DYNAMIXEL
(servomotor)
AX-12+ : 4EA AX-12+ : 18EA AX-12+ : 18EA
Sensor AX-S1 AX-S1 GYRO, DMS, IR
S/W BIOLOID SOFTWARE BIOLOID SOFTWARE RoboPlus
Power Eneloop Ni-MH 9.6V
SMPS 12V 5A
Eneloop Ni-MH 9.6V
SMPS 12V 5A
Li-Po 11.1V
SMPS 12V 5A
Remote Control RC-100 +
ZIG-100 set (Option)
RC-100 +
ZIG-100 set (Option)
RC-100
ZIG-110 set (Option)
Manual Quick Start (14 robots)
User's Guide
Quick Start (26 robots)
User's Guide
Quick Start (3 robots)
e-manual (26 robots)
Usage Education(School) Education(School/Univ.)
Entertainment/Hobby
Education(School/Univ.)
Competition/Entertainment
/Hobby

Monday, November 08, 2010

Bioloid Premium robot

The Robotis Bioloid Premium Robot Kit is an all-in-one package for advanced robot builders. The BIOLOID is do-it-yourself educational robot kit using modular DC servo blocks. Build your own robot and upgrade it with enhanced mobility & intelligence. Inspiring the creative minds worldwide, the evolution of BIOLOID continues. Note: we strongly discourage the use of liquid type or Loctite 242, which may damage frame parts. Stick type Loctite 248 and 268 is acceptable.

Features:
• Excellent humanoid walking performance (Adjusting posture while walking)
• Various sensors including Gyro, distance, IR and more external ports
• Remote control capability (IR-default, Zigbee-optional)
• C-Style programming & motion teaching with RoboPlus S/W (USB interface included)
• Transparent humanoid skin for customization
• Digital Packet communication with daisy chain topology
• Building various robots using versatile expansion mechanism

Applications:
• Spider
• Dinosaur
• Puppy
• Humanoid
• CM-510 (Main Controller- ATMEGA 2561)
• AX-12+ (Robot Actuator, Dyanmixel) x 18
• Gyro Sensor (2 Axis)
• Absolute Distance Measurement Sensor
• IR Sensor x 2
• RC-100 (Remote Controller)
• Head & Chest Skin
• SMPS for external power (12V, 5A)
• Rechargeable Battery (11.1V, Li-Po, 1000mA/PCM)
• Balance Battery Charger
• Screw Driver
• Cable Holder
• Quick Start
• Software CD (Windows XP / 2000 / Vista 32bit)
• Height: 397mm (15.6 inch) / A Type
• Weight: 1.7 kg (59.96 oz)
• USB2Dynamixel
• ZIG-100 included for a limited time only

SIZE:
• Height (mm): 397
• Width (mm): 190
• Depth (mm): 100
• Weight: 1.7Kg

Wednesday, September 16, 2009

BIOLOID EXPERT KIT

BIOLOID EXPERT KIT
Complete robot KIT, For advance users.

INCLUDES:

* AX-12+ - Dynamixel : 21 pcs [Torque : 12.5kgf.cm at 7V]
* AX-S1 : Dynamixel Sensor : 3 set
* CM-5 (Main Controller ) : 2 pcs (including batteries)
* ZIG-100 (Wireless Module ) : 1 set
* ZIG2Serial
* USB2Dynamixel
* Wireless Camera Set
* Image Recognition Library Support
* Wireless Communication with PC
* SMPS (12V, 5A) : 1 [For power supply and charging]
* Frame Set : 2 sets
* Spare Cable Sets
* Software CD
* Quick Start : 26 different robot assembly directions including intro and download information
* User Guide (Manual)
* Expert Manual (C Language Examples Available)
* Aluminum Case