HILO ALL-100A Universal & Gang Programmer, A high performance programmer for both engineering & production.
ALL-100A programmer is a revised version of ALL-100 programmer. Major enhancements include: The revised core processor with built-in 8K-byte cache speeds up programming time by 10% ~ 50%; The regulated device supply voltages further improve IC programming stability; The new USB processor further speeds up and stabilizes data link / transfer.
ALL-100A programmer has 68 sets of Precise Universal Pin Driver to provide high speed, low noise, accurate and reliable programming signals for various IC products including high speed low power devices recently released to market. ALL-100A can be setup for either single-site programming for engineering or multi-site programming for production. If required, up to 8 sets of ALL-100A can be setup for multi-set operation so up to 64 sites can be programmed simultaneously to maximize production. The supporting software is updated weekly on web site for check / retrieve through Internet. Programming of new products will not be neglected after purchasing.
Features & Benefits :
■ Excellent performance :
ALL-100A’s high freq. core circuit design significantly cut down programming time for around 10% ~ 50%. Universal Pin Drivers provide high speed, low noise, accurate and reliable programming signals for various IC products including high speed low power devices recently released to market.
■ Wide range of IC coverage :
ALL-100A supports wide range of IC products including EPROM, EEPROM, Serial PROM, SPI memory, FLASH, MPU/MCU product types and DIP, SDIP, SOP, SSOP, TSOP, PLCC, QFP, QFN, SON, BGA package types.
■ Easy to setup, operate and maintain :
ALL-100A setup and operation can be done easily by connecting Programmer to PC with Windows 2000 / XP / Server 2003 / Vista through USB port, load data file or read Master IC, then select functional options (Program, Verify, Auto...etc.) to start programming. The self-diagnostic utility makes programmer easy to checkout / maintain.
ALL-100A setup and operation can be done easily by connecting Programmer to PC with Windows 2000 / XP / Server 2003 / Vista through USB port, load data file or read Master IC, then select functional options (Program, Verify, Auto...etc.) to start programming. The self-diagnostic utility makes programmer easy to checkout / maintain.
■ High expansion flexibility :
From development / engineering stage using ALL-100A single-site programming to limited production stage using ALL-100A multi-site / multi-set programming, further to mass production stage using AT3-3XX automated programming, high expansion flexibility of programming platform is well prepared in advance.
Specification
■ Core controller
16 bits high freq. core control circuit with big sized FPGA & CPLD
■ Key functions
Load File, Read Master, Program, Verify, Auto, ID Check, Checksum, Blank Check,
Erase, Security, Protect / Unprotect, Edit, Function Configuration, Self Test.
■ Support devices
IC types : EPROM, EEPROM, Serial PROM, SPI memory, FLASH, MPU/MCU…etc.
IC packages : DIP, SDIP, SOP, SSOP, TSOP, PLCC, QFP, QFN, SON, BGA…etc.
IC leads : 8 pins ~ 300 pins
■ Device contact
Default : DIP48 ZIF single socket on Programming Module
Others : Dedicated sockets on Programming Module per IC package type
■ I/O channels
ALL-100A single-site : 48 sets of Precise Universal Pin Driver
ALL-100AP multi-site : 68 sets of Precise Universal Pin Driver
■ Parallel programming
ALL-100A : Single-site programming
ALL-100AP : Multi-site programming. Up to 8 sites per set.
■ Operation control
Base Unit : YES button – Start programming
ON indicator – Programmer on / ready BUSY indicator – Under programming
Socket Module : OK indicator – Pass programming
■ Data transfer interface
Transfer port : USB x 1
Transfer speed : USB1.1 : 12 Mb/sec. USB2.0 : 480 Mb/sec.
■ Host computer requirement
An Intel Pentium 4 or compatible processor with 512MB of RAM
At least one USB port is available (V1.1 / V2.0)
50MB free hard disk space
Windows 2000 / XP / Server 2003 / Vista operation system
CD ROM / DVD ROM Drive
■ Power
Power source : 100~240 VAC 50~60 Hz
Power consumption : ~ 0.5 A
■ Dimension
W x D x H 150mm x 260mm x 100mm
■ Weight
~ 4.0 kg
■ Operation temperature
0 ~ 40 C (32 ~ 105 F)
■ Certification
CE certified
■ Core controller
16 bits high freq. core control circuit with big sized FPGA & CPLD
■ Key functions
Load File, Read Master, Program, Verify, Auto, ID Check, Checksum, Blank Check,
Erase, Security, Protect / Unprotect, Edit, Function Configuration, Self Test.
■ Support devices
IC types : EPROM, EEPROM, Serial PROM, SPI memory, FLASH, MPU/MCU…etc.
IC packages : DIP, SDIP, SOP, SSOP, TSOP, PLCC, QFP, QFN, SON, BGA…etc.
IC leads : 8 pins ~ 300 pins
■ Device contact
Default : DIP48 ZIF single socket on Programming Module
Others : Dedicated sockets on Programming Module per IC package type
■ I/O channels
ALL-100A single-site : 48 sets of Precise Universal Pin Driver
ALL-100AP multi-site : 68 sets of Precise Universal Pin Driver
■ Parallel programming
ALL-100A : Single-site programming
ALL-100AP : Multi-site programming. Up to 8 sites per set.
■ Operation control
Base Unit : YES button – Start programming
ON indicator – Programmer on / ready BUSY indicator – Under programming
Socket Module : OK indicator – Pass programming
■ Data transfer interface
Transfer port : USB x 1
Transfer speed : USB1.1 : 12 Mb/sec. USB2.0 : 480 Mb/sec.
■ Host computer requirement
An Intel Pentium 4 or compatible processor with 512MB of RAM
At least one USB port is available (V1.1 / V2.0)
50MB free hard disk space
Windows 2000 / XP / Server 2003 / Vista operation system
CD ROM / DVD ROM Drive
■ Power
Power source : 100~240 VAC 50~60 Hz
Power consumption : ~ 0.5 A
■ Dimension
W x D x H 150mm x 260mm x 100mm
■ Weight
~ 4.0 kg
■ Operation temperature
0 ~ 40 C (32 ~ 105 F)
■ Certification
CE certified
