Friday, January 30, 2009

GPS signal enhancer

Limited Stock: GPS Signal Enhancer. For use inside Car.

Usually GPS (Handphone GPS) has less signal, even no signal if operate inside the car. External GPS Antenna not supported for several GPS hardware cause there are no connector built in the hardware.

This Device eliminate the problem, no external antenna required. Only this device! No GPS hardware modification. The Power supply consumption just from car cigarette lighter and connected to the GPS small antenna part. As simple as the hardware, The round antenna work by re-radiate GPS singnal, then your GPS receive more strength signal.

Thursday, January 29, 2009

CMUCam 2 pkg with OV6620


The new version of the CMU Camera. This version incorporates a on-board frame buffer allowing much more flexibility in image manipulation, sub-sampling, and higher frame rates. This version comes completely assembled.

More Details:

The CMUCam2 consists of a SX52 microcontroller interfaced with an OV6620 Omnivision CMOS camera on a chip that allows high level data to be extracted from the camera's streaming video.

The CMUCam2 communcicates via a RS-232 or a TTL serial port that has the following functionallity:

* Track user defined color blobs at up to 50 frames per second
* Track motion using frame differencing at 26 frames per second
* Find the centroid of any tracking data
* Gather mean color and variance data
* Gather a 28 bin histogram of each color channel
* Manipulate horizontally pixel differenced images
* Transfer a real-time binary bitmap of the tracked pixels in an image
* Arbitrary image windowing
* Adjust the camera's image properties
* Dump a raw image (single or multiple channels)
* Up to 176x255 resolution
* Supports multiple baudrates (115200, 57600, 38400, 19200, 9600, 4800, 2400, 1200)
* Control 5 servo outputs
* Slave parallel image processing mode off of a single camera bus
* Automatically use servos to do two axis color tracking
* Flexible output packet customization
* Multiple pass image processing on a buffered image

most update manual:
http://www.cs.cmu.edu/~cmucam2/

Friday, January 23, 2009

5 Watt Solar Cell Panel

5 WATT SOLAR PANEL

Specifications:
  • Max power 5 watt
  • Max voltage 17.28 DCV at 0.32A
  • Weight 780 gr
  • Dimension 292 x 214 x 18 mm.
more info about solar cell here

Switching Power Supply 24 Volt 3 Ampere


Switching Power Supply 24 Volt 3 Ampere.
Application for: printer, power over ethernet, power (accu) charger, general application, etc.

Thursday, January 22, 2009

Memsic 2125 dual-axis accelerometer

The Memsic 2125 is a low cost, dual-axis thermal accelerometer capable of measuring tilt, acceleration, rotation, and vibration with a range of ±3 g. Many exciting applications for the Memsic Accelerometer may be found in our Smart Sensors & Applications text .

Features of the Memsic 2125:
• Fully temperature compensated over 0 to 70 °C range
• Analog output of temperature (TOut pin)
• Low current 3.3 or 5 V operation: less than 4 mA at 5 VDC

Emic Text-to-Speech Module

This module will let your robot speak, provide a real human console interface to your control system, or simply provide some entertainment to your Parallax microcontroller projects. Based on the Winbond WTS701, this device intelligently handles values, sentences, numbers andcommon abbreviations with an extremely natural female voice with simple serial string sentences.

Features of the Emic Text-to-Speech Module:
• Capable of embedded phonetic control for foreign and difficult-topronounce words
• Easy-interface SIP format 2.0 x 1.375 in. with 0.1 inch pin spacing
• Single 5 V supply with TTL serial interface (2-wire, 2400 baud)
• On-board 300 mW speaker driver
• Easy-to-use ASCII or hexadecimal command sequences
• Bi-color LED for visual feedback of activity
• Audio input pin for amplification of BASIC Stamp-generated sounds and sound effects
• Compatible with BASIC Stamp 2 module (and a PC serial port when connected using a MAX232 line driver)

Parallax’s Serial LCDs

Parallax’s Serial LCDs are very functional, low-cost solutions for adding displays to your microcontroller applications. They support ASCII decimal characters 32-127 (the same visible characters as the BASIC Stamp Editor’s Debug Terminal). In addition, you may define up to eight custom characters. Text wrapping to the next line is automatic. Additional control codes allow you to place the cursor anywhere on the display, and turn the display on or off with a single instruction.

Features include:
• Switch-selectable baud rates: 2400, 9600, and 19200
• Adjustable contrast dial
• Simple 3-pin 0.1 inch SIP connection for RX, power and ground
• Power requirements: 5 VDC; 20 mA backlight off, 80 mA backlight on
• Operating temperature: -4 to +158 °F (-20 to +70 °C)
• Dimensions: 2x16 modules, 1.5 x 3.15 in (3.8 x 8 cm); 4x20 module, 2.4 x 3.9 in (6 x 10 cm). Sizes are approximate and may vary.

wallmounted rack , 2 door access


Technical Specifications:
Size : 12 U
Overall Height (mm) : 615
Usable Height (mm) : 534
Overall Depth (mm) : 490
Usable Depth (mm) : 381
Overal Width (mm) : 590
Usable Width (mm) : 450
Weight (Kg) : 38

Wednesday, January 21, 2009

CF Interface RFID Reader module for PDA

Introduction:

PCR125 / MFR135 / RWD145 is a compact RFID reader module for PDA / Pocket PC with CF card interface. Easy to install RFID Reader module to PDA, just plug in PROMAG RFID reader module to CF card slot in PDA and install PROMAG demo program to computer, by way of data synchronizations to PDA. Then RFID reader module is able to read RFID tags by PDA connectivity.

Features:

�� Compatible with any PDA with CF interface
�� Support Windows CE operation system
�� Contactless reading
�� Small and compact design
�� Easy to install
Applications:
�� Data collection terminal
�� Access control terminal
�� Time and Attendance
�� Logistics system
�� Guard tour terminal

Available Versions :

PCR125 --- 125Khz / Read only
MFR135 --- 13.56Mhz / Read only
RWD145 --- 13.56Mhz / Read & Write

MFR120 Mini Portable Mifare/Felica UID Reader/ Data Collection Terminal

Introduction:
MFR120 is a Mini portable battery-powered Mifare/Felica UID reader with LCD and built-in real time clock for data collection applications. MFR120 is designed for Mifare/Felica card data collection anytime and anywhere without computer connectivity. How does MFR120 work?
The data is read from MFR120 Mifare/Felica UID reader and shown on the display and kept into the memory with time stamp and downloaded to the computer.


Features:

�� 512K bytes memory
�� Built-in Real Time Clock (RTC) and back-up capacitor
�� Battery-powered portable, small footprint
�� Physical reader can read 13.56MHz Mifare/Felica cards
�� LCD display (101 x 67 dots)
�� Auto off for power saving
�� Low battery indicator
�� Memory full indicator

Applications:

�� Employee’s Time/Attendance data collection
�� Exhibition visitors’ data collection
�� Conference attendants data collection
�� Guard tour monitoring system
�� Student attendance data collection