Wednesday, May 28, 2014

Low Cost Dekko 86D General Multimeter

Dekko 86D General Multimeter


Specifications:

  • DCV 200mV - 1000V +/- 5% 
  • ACV 0V - 750V +/- 1.2%
  • DCAmp : 20mA - 10A +/- 2%
  • Resistance 200 Ohm - 2000K Ohm +/- 1.2%
  • Simple Transistor test YES
  • Diode test YES
  • Continuity Buzzer : YES
  • Power 9V Battery

Monday, May 26, 2014

PG-PROXL-6C-1-W1 Dustproof and waterproof UHF smart label

PG-PROXL-6C-1-W1 Dustproof and waterproof UHF smart label

Specification:

•Size: 96 x 22 mm
•Operating Frequency: 860-960MHz
•Tag Protocol: EPC C1 Gen2(ISO18000-6C)
•Chip Type: Alien H3
•Memory Capacity: 512Bits(96Bits EPC,64Bits TID)
•Working Mode: FHSS, fixed frequency transceiver
•Operating R/W: For both Reading & Writing
•Operating Range: 0-15m(depends on different readers)
•Data Retention: 10 years
•Erase-Write: 100,000 times
•Operating Temperature: -25°C~60°C
•Storage Temperature: -25°C~65°C

PG-PROXL-UHF-6C-B1 Vehicle Anti-dismantle UHF smart label / Tag

PG-PROXL-UHF-6C-B1 Vehicle Anti-dismantle UHF smart label / Tag


Specification:

•Size: 110 x 40 x 0.3mm
•Operating Frequency: 860-960MHz
•Tag Protocol: EPC C1 Gen2(ISO18000-6C)
•Chip Type: Alien H3
•Memory Capacity: 512Bits(96Bits EPC,64Bits TID)
•Working Mode: FHSS, fixed frequency transceiver
•Operating R/W: For both Reading & Writing
•Operating Range: 0-12m(depends on different readers)
•Data Retention: 8 years
•Erase-Write: 100,000times
•Operating Temperature: -25°C~60°C
•Storage Temperature: -25°C~65°C

PK-UHF201-1 868MHz Long Range UHF RFID Reader and Writer

PK-UHF201-1 868MHz Long Range UHF RFID Reader and Writer

Specifications 
•Dimension: 445 x 445 x 65mm
•Net Weight: 2600g
•Gross Weight: 5000g
•Protocol: ISO18000-6B, EPC Class 1 Gen2(ISO18000-6C)
•Protection Grade: IP54
•Work Frequency: Standard ISM 865-868MHz(PK-UHF201-1)

•Frequency Hopping: FHSS
•Power Output: 0-30dBm(adjustable)
•Antenna: Built-in 12dBi linearized polarizedantenna
•Interface: RS232, RS485, wiegand 26/34(TCP/IP,Wifi can be customized)
•Operating Mode: Answer,Active,Trigger
•Read Range: 0-15m
•Write Range: 0-6m
•Reading Clue: Buzzer
•Input Power: 100-240V,DC+9V (Power Adapter)
•Power Consumption: 1W
•Operation Temp: -25°C~+60°C
•Storage Temp: -25°C~+80°C
•Humidity: 80%
•Regulatory: Compliant with CE,FCC
•Additional services: Provide Demonstration software andSDK for further development.

PK-UHF201 928MHz Long Range UHF RFID Reader and Writer

PK-UHF201 928MHz Long Range UHF RFID Reader and Writer

Specifications 
•Dimension: 445 x 445 x 65mm
•Net Weight: 2600g
•Gross Weight: 5000g
•Protocol: ISO18000-6B, EPC Class 1 Gen2(ISO18000-6C)
•Protection Grade: IP54
•Work Frequency: Standard ISM  
902~928MHz (PK-UHF201
)•Frequency Hopping: FHSS
•Power Output: 0-30dBm(adjustable)
•Antenna: Built-in 12dBi linearized polarizedantenna
•Interface: RS232, RS485, wiegand 26/34(TCP/IP,Wifi can be customized)
•Operating Mode: Answer,Active,Trigger
•Read Range: 0-15m
•Write Range: 0-6m
•Reading Clue: Buzzer
•Input Power: 100-240V,DC+9V (Power Adapter)
•Power Consumption: 1W
•Operation Temp: -25°C~+60°C
•Storage Temp: -25°C~+80°C
•Humidity: 80%
•Regulatory: Compliant with CE,FCC
•Additional services: Provide Demonstration software andSDK for further development.

NXP LPC-H1343

NXP LPC-H1343
DEVELOPMENT PROTOTYPE HEADER BREAKOUT BOARD FOR LPC11XX CORTEX M0 ARM MICROCONTROLLER


FEATURES
  • Power supply circuit
  • Power-on led
  • USB connector only for power supply, not USB functionality
  • Debug interface – SWD (Serial Wire Debug)
  • Reset button
  • Prototype area
  • FR-4, 1.5 mm, soldermask, component print
  • Dimensions:38.1 x 38.1mm (1.5 x 1.5")

Deadbolt Releaser DAR-24

Product Name : Deadbolt Releaser (with patent)

Model : DAR-24

Product Description
Deadbolt releaser is the device installed on the door panel to pair with the general deadbolt lock which is installed on the door jamb for auxiliary releasing the bolt during either in damaged or power failing condition. Especially for the fail safe type power bolt which is unable to release the bolt during power failure.

Suitable for deadbolt: DA-64, DA-62A/D series, could support dead bolt of other brand also.

Applications
For aluminum, steel, wooden or brass door

PG-DASTC-2 Glass jig for DA-L62 / DA-64

Product Description:
Glass jig for power bolts DA-L62, DA-64

Dimensions: Unit(mm) PG-B64 External hanging basket +PG-DASTC-2 Glass jig



Electric Deadbolt(Standby current 18mA only) (DA-64)

Product Name : Electric Deadbolt(Standby current 18mA only)
Model : DA-64

Features
•Fail safe type released as power off.
•With magnetic switch door position sensor
•With DIP switch for setting time delay for opening & relock door
•Electric drop bolt design suitable for double swing door with 180° opening angle
•With power & state LED indicator
•Low stand by current (18mA) suitable for battery backup in fail secured application.
•Low working current, no over heating problem.
•With exit function thru low current contacts.

Specifications
•Lock size (mm):204(L) x 33(W) x 45(D)
•Approx. weight:675g ±1%
•Nominal voltage:DC12V
•Voltage tolerance:±10%
•Standby current:18mA
•Working current:440mA
•Temp. range:-20°C ~ 70°C
•Power consumption:0.2W(standby) / 5.3W(work)

Application
As auxiliary lock for emergency door, swing glass sheet door, frameless glass door, wooden door.

Accessories
External hanging basket - PG-B64 (separate purchase)

Sunday, May 25, 2014

PG-DASTC-1 External hanging basket for power bolts DA-L62

PG-DASTC-1 External hanging basket for power bolts DA-L62 

Product Name : External Hanging Basket for Power Bolts DA-L62
Model : PG-DASTC-1

Specifications
•Dimensions Body: 211(L) x 45(W) x 50(H)
•Magnetic lump: 106(L) x 45(W) x 50(H)

Dimensions: Unit(mm)
PG-DASTC-1 External hanging basket + PG-DASTC-2 Glass jig

Electric deadbolt lock DA-L62

Electric Deadbolt (Drop to hold position by magnetic)
Model : DA-L62


Features
•Fail safe type.
•Release as power off.
•With electronics control for over heating.
•With door monitoring and adjustable door release monitoring time.
•With adjustable timer to lock.
•Glass door w/o frame dedicated.
•Pair with bracket PG-DASTC-1 and PG-DASTC-2.
•With magnetic switch fordoor position sensor
•Operation:Drop to hold position by magnetic.

Specifications
•Lock size:205(L) x 32(W) x 43(D)mm
•Approx. weight:900g
•Nominal voltage:DC12V
•Voltage tolerance:±10%
•Standby current:380mA
•Working current:900mA
•Temp. range:-20°C ~ 70°C
•Power consumption:3.6W(standby) / 12W(work)

Application
As auxiliary lock for emergency door swing glass sheet door

Accessories
External hanging basket - PG-DASTC-1

Saturday, May 24, 2014

NXP LPC-H11U14

NXP LPC-H11U14
DEVELOPMENT PROTOTYPE HEADER BREAKOUT BOARD FOR LPC11XX CORTEX M0 ARM MICROCONTROLLER

FEATURES

  • Power supply circuit
  • Power-on led
  • USB connector only for power supply, not USB functionality
  • Debug interface – SWD (Serial Wire Debug)
  • Reset button
  • Prototype area
  • FR-4, 1.5 mm, soldermask, component print
  • DDimensions:38.1 x 38.1mm (1.5 x 1.5")

NXP LPC-H11C14

NXP LPC-H11C14
DEVELOPMENT PROTOTYPE HEADER BREAKOUT BOARD FOR LPC11XX CORTEX M0 ARM MICROCONTROLLER


FEATURES


  • Power supply circuit
  • Power-on led
  • USB connector only for power supply, not USB functionality
  • Debug interface – SWD (Serial Wire Debug)
  • Reset button
  • Prototype area
  • FR-4, 1.5 mm, soldermask, component print
  • Dimensions:38.1 x 38.1mm (1.5 x 1.5")

NXP LPC-H11A14

NXP LPC-H11A14
DEVELOPMENT PROTOTYPE HEADER BREAKOUT BOARD FOR LPC11XX CORTEX M0 ARM MICROCONTROLLER


FEATURES


  • Power supply circuit
  • Power-on led
  • USB connector only for power supply, not USB functionality
  • Debug interface – SWD (Serial Wire Debug)
  • Reset button
  • Prototype area
  • FR-4, 1.5 mm, soldermask, component print
  • Dimensions:38.1 x 38.1mm (1.5 x 1.5")

Friday, May 23, 2014

Analog I/O module

Analog Input / Output module consisting of an Analog to Digital Converter and Digital to Analog ADC0809CCN TLC5628CN Converter . So that these modules can be used to convert digital data into analog voltage and vice versa to change the voltage analog to digital data . This module is suitable for applications gauge / temperature controller , motor speed control , robotics , etc. .

specifications :
- 8 -channel 8 - bit Analog to Digital Converter ( ADC ) :
Analog input range 0-5 Volts .
The conversion time of 100 us .
The maximum error + / -1 LSB .
Parallel interface compatible with TTL level .
Can work stand alone .
Available jumper to set the channel address pins in hardware .

- 8 -channel 8 - bit Voltage Output Digital to Analog Converter ( DAC ) :
Range analog output can be programmed 1x or 2x ( 0 to 2.5 Volt or 0-5 Volt )
Settling Time 10 ms .
The maximum linearity error + / -1 LSB .
Serial interface .
- Requires 5 Volt DC power supply .
- There are examples of programs for the DT - 51 and DT Series Low Cost Low - Cost AVR Series in BASIC and C language compiler is using BASCOM - 8051 and mVision2 for MCS- 51 and BASCOM -AVR compiler for AVR and CodeVisionAVR .

Thursday, May 22, 2014

XL-320 dynamixel

XL-320 dynamixel
Dynamixel servo motor families are packaged in small dimensions and has been equipped with a PID controller. Dynamixel XL-320 is compatible for use with the open source controller OpenCM 9:04 from Robotis.

H/W Specification
  • Weight : 16.7g
  • Dimension : 24mm *36mm * 27mm
  • Resolution : 0.29°
  • Motor : Cored Motor
  • Gear Reduction Ratio : 238 : 1
  • Stall Torque : 0.39 N.m (at 7.4V)
  • No load speed : 114 rpm (at 7.4V)
  • Running Degree: 0° ~ 300° § Endless Turn
  • Running Temperature : -5℃ ~ +70℃
  • Voltage : 6 ~ 8.4V (Recommended Voltage 7.4V)
  • Command Signal : Digital Packet
  • Protocol Type : Half duplex Asynchronous Serial Communication (8bit,1stop,No Parity)
  • Link (Physical) : TTL Level Multi Drop (daisy chain type Connector)
  • ID : 253 ID (0~252)
  • Communication Speed : 7343bps ~ 1 Mbps
  • Feedback : Position, Temperature, Load, Input Voltage, etc.
  • Material : Engineering Plastic

OpenCM9.04 controller

Microcontroller module based on ARM Cortex-M3 (STM32F103CB) from Robotis. This microcontroller module can be used as a microcontroller module in general. As one of the other advantages (in addition to high-level processing) of this module is its compatibility with a wide range of robotic products, including intelligent servo Dynamixel (TTL), ZIG-110A, BT-110A, etc.. This module programming can be done easily using robotic OpenCM IDE that has the look and structure of the language that is similar to the Arduino IDE. 

Benefit:
  • OpenCM9.04 is a microcontroller board based on 32bit ARM Cortex-M3. The OpenCM9.04’s schematics and source codes are open-source.
  • 2 types are available: Type A & Type B. The difference between Type A & Type B is the availability of the connectors. (Refer to the image and table above.)
  • (OpenCM9.04 Accessory Set can be purchased to acquire all the necessary connector to upgrade Type A to Type B.) 

OpenCM9.04 Types Package
Power Switch
X
1
User Button
1
1
2Pin Battery(LBS-40)
X
2
JTAG/SWD
X
1
 Micro B USB
X
1
5-Pin Port
X
4
Dynamixel TTL BUS
X
4
4 Pin Communication
X
1


specifications: 
- Power Supply: 7V - 16V (USB 5V, 12V Dynamixel) 
- Based microcontroller / microprocessor: STM32F103CB (ARM Cortex-M3) 
- Number of I / O ports: 26 
- Port interfaces: CAN, USART, SPI, I2C, USB, 3-Dynamixel pin, External Sensors (5-pin), etc.. 
- Bootloader: internal 
- Port programming: micro USB & JTAG 
- Features: using IDE Robotis OpenCM similar to the Arduino IDE, compatible with a wide range of robotic products 
- Dimensions: 27 mm x 66.5 mm

Hioki 3287 Clamp On AC/DC True RMS HiTester.

Hioki 3287 Clamp On AC/DC True RMS HiTester.
Compact & easy, one-touch maintenance on all types of AC/DC equipment




  • Can handle even cogenerator / inverter energy-saving equipment
  • Use for high current measurements such as UPS emergency batteries and train motors
  • Slim core of only 10 mm(0.39 in) for easy clamping even in crowded wiring
Specifications
AC Current range10.00 or 100.0 A AC, 2 ranges (±1.5 % rdg. ±5 dgt. at 50 or 60Hz), Effective value rectifier
DC Current range10.00 or 100.0 A AC, 2 ranges (±1.5 % rdg. ±5 dgt.)
AC Voltage range4.200 to 600 V AC, 4 ranges (±2.3 % rdg. ±8 dgt. at 50 or 60Hz), Effective value rectifier
DC Voltage range420.0 mV to 600 V DC, 5 ranges (±1.3 % rdg. ±4 dgt.)
Other functionsResistance: 420.0 to 42.00 M-ohm, 6 ranges
Accuracy: ±2.0 % rdg. ±4 dgt. (at 420 to 420 k-ohm range)
Continuity: 420.0 ohm (Buzzer sounds at approx. 50 ohm or less)
Analog outputNone
Frequency characteristics (at AC current / voltage)AC current: 10 to 1 kHz, AC voltage: 30 to 500 Hz
Display sectionDigital / LCD, maximum 4199 dgt.
Sampling rate2.5 times/sec
Crest factor (RMS)2.5 or less (150 A, 1000 V maximum)
Max. circuit voltage600 V AC rms (insulated wire)
Power supplyCR2032 (3 VDC) × 1, Continuous use 25 hours
Core jaw diameter35 mm(1.38 in)
Dimensions (WxHxD), Weight57 mm(2.24") x 180 mm(7.09") x 16 mm(0.63"), 170 g (6.0 oz)

Fluke 789 ProcessMeter™

Fluke 789 ProcessMeter™
Now compatible with Fluke Connect™ App


The Fluke 789 ProcessMeter is the ultimate troubleshooting tool for electricians and instrumentation professionals, combining the functionality of a loop calibrator with the power of a digital multimeter. By equipping the 789 with a temperature measurement module and the wireless data logging capabilities of Fluke Connect™ with ShareLive™ video call (sold separately), process technicians can now do a lot more while carrying a lot less. And with its built-in, selectable 250 ohm HART® resistor, it eliminates the need to carry a separate resistor with you.

Model NameDescription
Fluke 789Fluke 789 ProcessMeter™ 
Includes:

  • Fluke 789 ProcessMeter
  • AC175 Alligator Clips
  • Four (4) AA 1.5 V alkaline batteries (installed)
  • TL71 safety-designed test lead set

Features of the Fluke 789:
  • 24 V Loop power supply
  • Very large dual display
  • Enhanced backlight with 2 brightness settings
  • 1200 ohm drive capability on mA source
  • HART mode setting with loop power and a built-in 250 ohm resistor
  • 0% and 100 % buttons to toggle between 4 and 20 mA sourcing for a quick span check
  • Externally accessible fuses for easy replacement
  • Infrared-port to process data in FlukeView Forms (V2.1) software

Fluke 789 features that are also included in the Fluke 787:
  • Precision 1000 V, 440 mA True-RMS digital multimeter
  • 0.1% dc voltage accuracy
  • 0.05% dc current accuracy
  • Frequency measurement to 20 kHz
  • Min/Max/Average/Hold/Relative modes
  • Diode Test and Continuity Beeper
  • Simultaneous mA and % of scale readout
  • 20 mA DC current source / loop calibrator / simulator
  • Manual Step (100%, 25%, Coarse, Fine) plus Auto Step and Auto Ramp
  • Externally accessible battery for easy battery changes

Safety conformance
Meets 1000 Volt EN61010-1 CAT III standards and 600 Volt EN61010-1 CAT IV standards.

Specifications
Current measurementRange0-1 A AC or DC
Resolution1 mA
Accuracy0.2% + 2 LSD (DC)
Range0-30 mA
Resolution0.001 mA
Accuracy0.05% + 2 lSD
Current sourcingRange0-20 mA or 4-20 mA
Resolution0.05% of span
Drive capability24 V Compliance or 1200 Ω @ 20 mA
FrequencyTo 19.999 kHz, 0.005% + 1 LSD
ContinuityBeeps for resistance < 100 Ω
Voltage measurementRange0-1000 V AC (true-rms) or DC
Resolution0.1 mV to 1.0 V
Accuracy0.1% Rdg + 1 LSD (VDC)
Resistance measurementTo 40 MΩ, 0.2% + 1 LSD
Diode test2.0 V shoes diode voltage drop
Display current and % of spanYes
Auto Step, Auto RampYes

Environmental Specifications
Operating temperature-20 ºC to 55 ºC
Storage temperature-40 ºC to 60 ºC
Humidity (without condensation)95% up to 30 ºC
75% up to 40 ºC
45% up to 50 ºC
35% up to 55 ºC
Temperature coefficient0.05 x (specified accuracy) per ºC (for temperatures < 18 ºC or > 28 ºC)

Safety Specifications
Electrical safetyDesigned in accordance with IEC 1010-1, ANSI/ISA S82.01-1994 and CAN/CSA C22.2 No 1010.1-92
Overvoltage categoryIEC 1010-1 CAT III 1000 V
IEC 1010-1 CAT IV 600 V
Maximum voltage1000 V rms

Mechanical and General Specifications
Size50 x 100 x 203 mm (1.25" H x 3.41"W x 7.35" L)
Weight610 g (1.6 lbs)
Batteries4 AA alkaline batteries
Warranty3 years
Battery life140 hours typical (measurement), 10 hours typical (sourcing 20 mA)
Shock and vibrationRandom, 2 g, 5-500 Hz
1 meter drop test

Wednesday, May 21, 2014

Low Cost Man Machine Interface

Low Cost MMI is a Man ​​Machine Interface module is used as a means of interface between human and electronic systems . This module is composed of 8 -digit seven segment and 4 buttons .

This module can be used as input and displays the output in the motor speed controller applications , robotics , and other applications . As well as fully compatible with any microcontroller or minimum systems.

specifications :
- 8 -digit Seven Segment with 0.56 inch high type Super Bright Red .
- 4 buttons as input to the function depends on the application .
- Requires voltage + 5VDC as power supply .
- PCB design with industry standard 2 -layer FR4 material and Plated Through Hole ( PTH ) . As well as the use of SMD components ( Surface Mount Device ) makes PCB DT - I / O Low Cost MMI is more compact .
- There are examples of programs for the DT - 51 and DT Series Low Cost Low - Cost AVR Series in BASIC and C for MCS - 51 ( BASCOM - 8051 and mVision2 ) and AVR ( BASCOM - AVR and CodeVisionAVR ) .
- Supports DT - 51 Minimum System ver 3.0 , PetraFuz DT -51 , DT - BASIC Series , and the system microcontroller / microprocessor other .
- Equipment: 1 piece DT - board I / O Low Cost MMI , CD / DVD Program

Electric Power Bolt Lock DA-62A.

Electric Power Bolt Lock DA-62A/D, Fail Safe

Spesifications Electric Power Bolt Lock
  • Lock size L x W x D (mm) 205 x 38 x 44
  • Approx. Weight 1000g
  • Nominal voltage DC 12V
  • Stanby Current 310 mA
  • Working Current 1040 mA
  • Temp. range -20 ~ 70 deg celcius
  • Power consumption 3,7 W (Stanby), 12,5W (work)

Features Fail safe type
* release as power off
*with microswitch for sensoring door position
*with electronics control for over heating
Material Zinc Alloy
Operation Drop to hold positioning by magnet
Applications As auxiliary lock for emergency door, swing glass sheet door

Tuesday, May 20, 2014

LPC-H1114 CORTEX M0 ARM MICROCONTROLLER.

LPC-H1114 CORTEX M0 ARM MICROCONTROLLER.
DEVELOPMENT PROTOTYPE HEADER BREAKOUT BOARD FOR LPC11XX CORTEX M0 ARM MICROCONTROLLER


FEATURES
  • Power supply circuit
  • Power-on led
  • USB connector only for power supply, not USB functionality
  • Debug interface – SWD (Serial Wire Debug)
  • Reset button
  • Prototype area
  • FR-4, 1.5 mm, soldermask, component print
  • Dimensions:38.1 x 38.1mm (1.5 x 1.5")

Friday, May 16, 2014

4 x 4 Keypad Module

4 x 4 keypad Keypad Module is a module measuring 4 columns x 4 rows. This module can be used as input devices in applications such as digital security, datalogger, absenteeism, motor speed controllers, robotics, and so on. 

specifications: 
- 16 keys (with function depending on application). 
- Configuration 4 lines (input scanning) and four columns (output scanning). 
- Fully compatible with the DT-51 and DT Series Low Cost Low-Cost AVR Series. Supports DT-51 Minimum System ver 3.0, PetraFuz DT-51, DT-BASIC Series, and other systems. 
- Equipped with a sample program. 
- Dimensions: 9.3 cm (P) x 6.8 cm (L) x 1.5 cm (T) 
- Equipment: 1 piece DT-I / O 4 x 4 Keypad Module, 1 sheet manual.

3x4 Keypad Module.

3x4 Keypad Module is a keypad module measuring 3 columns x 4 rows. This module can be used as input devices in applications such as digital security, datalogger, attendance system , motor speed controllers, robotics, and so on. 

specifications: 
- 12 keys (with function depending on application). 
- Configuration 4 lines (input scanning) and 3 columns (output scanning). 
- Fully compatible with all +5V Minimum Systemver 
- Equipped with a sample program. 
- Dimensions: 9 cm (P) x 5.4 cm (L) x 1.8 cm (T) 
- Equipment: : 3 x 4 Keypad Module, a sheet of quick start.

Thursday, May 15, 2014

Phone Interface Ver 2.0

Phone Interface Ver 2.0 is a series CM8888PI based and compatible with DT-51 MinSys and support system microcontroller / microprocessor other. Comes ready to use routines and has 2 modes (with and without telephone telephone) for anti-distance applications and home automation. 

specifications: 
- Using a Hybrid Single standard transformers FCC part 68 as the magnetic coupling between the telephone line to the module. 
- Impedance 600 ohms. 
- Dual Tone Multi Frequency Decoder and Encoder. 
- Dial Pulse Decoder & Encoder. 
- Call Progress Detector. 
- Line Status Detector. 
- Ring Detector. 
- 2 Modes Phone Line Interface. 
- On / Off Hook Conditioning. 
- Equipment: 1 piece DT-Board I / O Phone Interface Ver 2.0 and CD / DVD program.

BeagleBoard single board computer

BeagleBoard single board computer


The USB-powered Beagle Board is a low-cost, fan-less single board computer utilizing Texas Instruments’ OMAP3530 processor that unleashes laptop-like performance and expansion without the bulk, expense, or noise of typical desktop machines.

Beagle Board is based on an OMAP3530 application processor featuring an ARM® Cortex™-A8 running at up to 720MHz and delivering over 1,200 Dhrystone MIPS of performance via superscalar operation with highly accurate branch prediction and 256KB of L2 cache. Focal to Beagle Board experience is the high-speed USB 2.0 on-the-go (OTG) port that can be utilized to provide power to the board or to deliver highly flexible expansion. Standard PC peripherals can be connected to Beagle Board using the USB with a mini-A to standard-A cable adapter, DVI-D using an HDMI to DVI-D adapter, or through the MMC/SD/SDIO connector enabling a complete desktop experience.

Key Features:
Industry’s highest performance ARM
-720MHz ARM Cortex-A8 (>1GHz ARM11 MIPS)
- NEON and VFP extensions for additional acceleration

State of the art POWERVR™ graphics hardware
- 10 million polygons per second
- Advanced tile-based rendering

Industry leading C64x+ DSP & video acceleration
- Streaming, portable media player, and high-res video

Tiny 3” x 3” PCB that can fit in your pocket
- Yet support for 1280x1024 DVI-D monitors

Community-Based Activity:
Development tools
  • Programming: gcc for ARM Cortex-A8
  • Programming: free, non-commercial TI compiler for C64x+
  • Utilities: serial and USB boot-loader tools
Kernels and drivers
  • Reference Linux kernel for testing board hardware
  • USB: hubs, keyboards, mice, Ethernet, WiFi, web cameras, and more
Linux distributions
Angstrom (Open Embedded), Debian, Ubuntu, Gentoo, and more

User mode applications
  • Productivity: AbiWord, Gnumeric, GIMP
  • Multimedia: FFmpeg, MythTV
  • Gaming: ScummVM, solitaire
These are just some examples of on-going community development projects on BeagleBoard.org

Wednesday, May 14, 2014

LPC-E2468.

LPC-E2468.
Microcontroller LINUX DEVELOPMENT PROTOTYPE BOARD WITH LPC2468 USB,ETHERNET, SD/MMC IN CREDIT CARD FORMAT


FEATURES
  • MCU: LPC2468
  • 16MB SDRAM
  • 128 MB NAN Flash
  • standard JTAG connector with ARM 2x10 pin layout for programming/debugging with ARM-JTAG
  • Ethernet 100MBit
  • 2x USB hosts
  • USB-to-RS232 converter device connected to LPC2468 UART
  • SD/MMC card connector
  • UEXT connector with I2C, SPI, RS232 and power supply for connecting add-on modules like RF link, MP3, etc available from Olimex
  • trimpot connected to ADC
  • RESET circuit with external control of Philips ISP utility via RS232 port
  • two USER button
  • RESET Button
  • two on board voltage regulators 3V and 5V with up to 800mA current
  • Extension port connector for many of microcontrollers pins
  • single power supply: External power supply, USB or JTAG connector
  • Battery holder and connector for the RTC
  • power supply led
  • FR-4, 1.5 mm, red soldermask, component print
  • Dimensions: 90x60mm (3.54 x 2.36")

IMPORTANT NOTE
The board price does not contain uclinux related support. The uclunux supplied with this board is working out of the box, there are also release notes which guide you how to build the uclinux image, but we can't offer you linux related support or to hand-held guide you how to build your own kernel image or how to develop your own applications under uclinux. The uclinux image and CD is provided "as is" and it is a demo software not a commercial product which Olimex supports, if you need linux related support, please contact a linux consultant.

LPC-E2294-8MB.



LPC-E2294-8MB.
DEVELOPMENT PROTOTYPE BOARD WITH USB, 4X CAN, RS232, ETHERNET


FEATURES
  • MCU: LPC2294 16/32 bit ARM7TDMI-S™t with 256K Bytes Program Flash, 16K Bytes RAM, EXTERNAL MEMORY BUS, RTC,4x 10 bit ADC 2.44 uS, 2x UARTs, 4x CAN, I2C, SPI, 2x 32bit TIMERS, 7x CCR, 6x PWM, WDT, 5V tolerant I/O, up to 60MHz operation
  • Standard JTAG connector with ARM 2x10 pin layout for programming/debugging with ARM-JTAG
  • Optional TRACE connector (not assembled)
  • 8MB (2 M x 32bit) 70 ns K1S321611C PSRAM
  • 2MB (256Kx16bit) 70ns TE28F160C3BD70 C3 INTEL FLASH
  • LCD 16x2 DISPLAY with BACKLIGHT (1MB version)
  • NOKIA 6610 TFT 128x128 12bit color LCD with backlight (8MB version)
  • SD/MMC card connector
  • USB to RS232 convertor, board can take power from USB port
  • RS232 driver and connector
  • Ethernet 100Mbit with DM9000E
  • 4x CAN drivers and connectors
  • UEXT connector for Olimex modules connection - MOD-MP3, MOD-RFID125, MOD-NRF24L01 etc.
  • RESET circuit with external control of Philips ISP utility via USB-RS232 virtual port
  • Jumpers for boot select from external memory
  • Jumpers for ISP/RUN mode
  • 2 BUTTONS
  • POTENTIOMETER connected to AIN0
  • I2C 24LC515 EEPROM on board
  • Two on board voltage regulators 1.8V and 3.3V with up to 800mA current

WiFi Dongle for pcDuino.

WiFi Dongle for pcDuino.

This USB Wifi dongle has been tested to work with the pcDuino, simply plug it into the USB port and you're ready to connect to a nearby wireless network without installing any driver! 
Wifi PcDuino is a WLAN module supporting IEEE 802.11 b/g/n standards with PH connector supporting USB 2.0 .This is a low cost compact WLAN module designed in the product with embedded system for the wireless connectivity.WIFI_PCDUINO both support RT5370.WIFI_PCDUINO WLAN Module is designed to operate in 2.4GHz ISM frequency band.
  
Specification
  • 1T1R mode with 150Mbps with PHY rates for both transmit and receiving
  • Dynamic data rate:
    • Maximum data rate up to 150Mbps
    • 11n: Legacy, Mixed and Green Field. 
  • Modes:
    • 11g: 54/48/36/24/12/9/6 Mbps (Auto Sensing) 
    • 11b:11/5.5/2/1 Mbps (Auto Sensing).
  • Support 20MHz/40MHz Bandwidth
  • Security support for 64/128 bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK (TKIP/AES)
  • Reverse Direction Grant Data Flow and Frame Aggregation
  • Cisco CCX Support
  • USB2.0
  • Operating Frequency: 2.412GHz~ 2.484GHz
  • Transmit Output Power: 802.11g 15+/-1dBm
  • Receive Sensitivity 11b: -78dBm @ 11Mbps (Typical);11g: -68dBm @ 54Mpbs (Typical)
  • Operating Voltage:3.3V
  • Antenna Port Impedance:50ohm
Operating System
  • Windows 2000/XP/VISTA/Win7
  • Wince 5.0 & 6.0
  • Linux 2.6.x